User manual HILTI DD130

[. . . ] DD 130 D GB F I NL P E DK SF N S TR EST Bedienungsanleitung Operating instructions 1­12 13­24 LV LT 370458 *370458* 1 1 2 3 4 5 6 78 9 10 11 12 57 56 DD 13 0 13 14 22 21 20 19 18 17 16 15 55 34 35 23 36 24 25 48 47 54 26 27 28 37 38 29 39 30 40 41 31 32 33 43 42 46 45 44 49 53 52 51 50 6. 1. 1 6. 1. 2 1 0 DD 6. 1. 2 3 13 0 2 DD 13 0 DD 13 1 6. 1. 3 3 6. 2 15 15 4 5 3 6. 3 15 DD 13 0 15 15 1 2 2 1 1 1 4 15 6. 4. 1 6. 5. 1 6. 6. 1 3 1 3 4 DD 13 0 1 2 1 2 2 3 6. 6. 2 6. 7. 1 7 5 DD 13 0 6. 7. 2 1, 4 2 6 1 2 4 5 6 2 1 3 3 6. 7. 3 3 6. 8 6. 9 3 4 D 2 6 4 D 1 5 0 13 2 5 4 1 1 5 3 6 6 7 2 6. 10 1 2 6. 11 6. 12 4 2 4 3 5 1 2 5 3 4 1 7. 2. 1 7. 2. 2 7. 3 2 1 1 3 2 1 4 4 4 1 90° 3 7. 4 3 2 2 7. 5 3 5 4 6 2 2 7 8. 5. 1. 1 2 8. 5. 1. 2 1 5 90° 4 1 1 0 1 0 1 1 3 2 DD130 diamond core drilling machine It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. k 31 k 32 k 33 k 34 k 35 k 36 k 37 k 38 k 39 k 40 k 41 k 42 k 43 k 44 k 45 k 46 Vacuum hose connector Vacuum pad Baseplate Chain arrestor Hand wheel On / off switch lock Pressure gauge Level indicator Adjusting lever Levelling screws Hole centre indicator Locating lugs Depth gauge Locking mechanism Mounting pins Chain tensioner Parts of the DD130 Core drilling machine Water swivel / extraction head Water flow indicator Level indicator Screwdriver (side handle) Side handle Water flow regulator Water hose connector Gear selector Gearing section Motor On / off switch Grip Overload indicator Supply cord with PRCD Rating plate Interface plate Screw plugs (water swivel / extraction head) Cover (water swivel / extraction head) Extraction connector Water swivel lock k Locking ring (water swivel / extraction head) 21 k Chuck 22 Drill stand k Grip 23 k Chain 24 k Columns 25 k Hex. wrench 26 k Carriage 27 k Release lever 28 k Specification plate 29 k Vacuum release valve 30 Water collector for hand-held use k Securing knob 47 k Clamping screw 48 k Depth gauge 49 k Water collector cup 50 k Centring ring 51 k Centring ring adaptor 52 k Seal 53 k Mounting plate 54 Water collector for use with the drill stand k Holder 55 k Water collector cup 56 k Seal 57 Contents 1. Declaration of conformity Page 14 14 14 15 15 17 20 21 22 23 23 see cover 13 1. [. . . ] When positioned correctly, press the baseplate against the work surface and remove your finger from the vacuum release valve. Before beginning drilling and during operation, it must be ensured that the pressure gauge pointer remains within the green area. Tighten the lock nuts to prevent further movement of the levelling screws. An additional means of securing the drill stand must be employed when drilling horizontally (e. g. a chain attached to an anchor, . . . ) 6. 7. 3 Securing the drill stand with a quick-release brace (e. g. Extend the hole centre indicator and then use it as an aid to bring the drill stand into alignment with the centre point of the hole to be cored. Position the end of the quick-release brace carefully in the inner oval of the baseplate (not on the level indicator or pressure gauge). Secure the baseplate by applying slight pressure with the quick-release brace. Tighten the lock nuts to prevent further movement of the levelling screws. Tighten the quick-release brace securely. 19 6. 8 Water collection system for use with the drill stand Use of the water collection system permits water to be drained away from the core bit thus avoiding soiling the surrounding area. Best results are achieved in conjunction with a wet-type vacuum cleaner. Use of the water collection system in conjunction with a wet-type vacuum cleaner is mandatory for overhead drilling. The water collector sleeve and seal must be of a size suitable for the core bit diameter used. Slacken the column adjusting lever until the locating lugs are disengaged. Close the adjusting levers until the locating lugs are fully engaged and the frame is again secured. Lift the holder and push the water collector cup under the retainer as far as it will go. Connect a wet-type vacuum cleaner to the water collector cup or connect a length of hose through which the water can flow away. 6. 9 Mounting the tool on the drill stand The release lever on the drill stand must be in the open position and the carriage should be at the top of its travel. The drilling advance mechanism must be locked (chain arrestor engaged). Fit the tool interface plate onto the two mounting pins on the drill stand. The switch lock is used to hold the switch in the ON position during sustained operation. 6. 11 Adjusting the drill stand drilling angle (In increments of 7. 5°; adjustable to max. [. . . ] Please ask your Hilti customer service department or Hilti sales representative for further information. Should you wish to return the electric tool yourself to a disposal facility for recycling, proceed as follows: Dismantle the tool as far as possible without the need for special tools. Use absorbent paper to wipe oily parts clean and collect any oil that runs out. On no account should oil be allowed to enter the waste water system or find its way into the ground. [. . . ]