User manual HERKULES O505

[. . . ] O505 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 12-13 14-15 Warning Symbol WARNING This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions. Serial Number Purchase Date Model Number Distributor 2 of 15 WARNING EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result in serious injury. · · · · · · · · · · · This equipment is for professional use only. Read all instruction manuals, tags, and labels before operating the equipment. [. . . ] Dispose of hazardous fluid according to all local, state and national guidelines. Wear the appropriate protective clothing, gloves, eyewear and respirator. If diaphragm fails, the fluid may be exhausted along with the air. 4 of 15 Model Information Model O500 Description One gun, one cup paint gun washer / recycler with diaphragm pump, filter-regulator, and timer. O500 for use with water based cleaning solutions or standard lacquer thinner solvents. C (mm. ) 35 (889) 35 (889) O505 Model shown: O500 C 01980973(200) A B Installation Installing the Gun Washer 1. Place gun washer on a level surface in a properly ventilated paint mixing room. Insert the white, plastic siphon plug into a fresh 5 gallon solvent can. Use a high quality, slow evaporating solvent, such as DuPont's 3661S or equivalent. Place the siphon tube into the 5-gallon can through the white plastic plug. Attach the flare nut end of the siphon tube to the flare fitting on the underside of the mini gun washer. Ground all equipment used or located in the gun washer area. Connecting the Air Line 1. Then, wrench tighten 1/4 turn. 5 of 15 Operation Preparing the Equipment to be washed 1. Remove all gauges and regulators. Long Stem Support CAUTION All pressure gauges must be removed before placing equipment in gun washer to avoid damaging the gauges. Short Stem Support 4. Lock the gun trigger in the open position by placing the trigger lock around the gun handle and trigger (see Fig. 1). Figure 2 01960415(254) Placing Equipment in the Gun Washer 1. To clean guns not mentioned here, use the long or short stem supports as needed (see Fig. For questions or adapter kits contact your paint gun washer distributor. The shorter support is designed for siphon feed and pressure feed guns of up to 2 quart capacity which are fitted with siphon tube intakes. The long support is designed to hold gravity feed guns or pressure feed guns that have been removed from the air and paint lines. All pressure gauges must be removed before washing the paint gun. Placing Paint Guns in Washer Siphon Feed Trigger lock #22BA Place siphon tube onto short stem support nozzle. Gravity Feed Figure 1 01970826 Place long stem support over one of the short stem supports. *For Gravity Feed, High Volume Low Pressure Guns an adapter kit (part number 23K) is available from your distributor for best cleaning. 6 of 15 Placing Paint Guns in Washer (cont. ) HVLP - Mattson Use gun manufacturer's fixtures. [. . . ] Press the water drain pin up (See Fig 3). Filter/Regulator Water drain pin Figure 3 01970836 CAUTION Do not change the setting of the filter/regulator. This could damage the filter/regulator or pump. 8 of 15 Troubleshooting Problem Gun washer will not turn on. Possible Solution 1. Make sure the limit valve (#M1C) on the side of the tank is in closed position. Make sure timer cam is engaging the limit valve (#M1C) on the shield assembly. [. . . ]