User manual HERKULES HCR3

[. . . ] 4 Model Information Installation Inspection Operation Maintenance Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] REPLACE IF DAMAGED. Page 3 of 8 Model Information SPECIFICATIONS Maximum crushing pressure Can capacity 2. 1 tons One 1-gallon can Three 1-quart cans Time to crush can Overall width Overall height Overall depth Chamber width Chamber height Chamber depth Required air pressure Total weight 20 seconds 18. 125" 25. 25" 13. 5" 10" 10" 10" 90-120 p. s. i. 75 Ibs. OWNER/OPERATOR RESPONSIBILITY It is the owner/operator's responsibility to properly use and maintain this equipment. The instructions and warnings contained in this manual shall be read and understood by the owner/operator prior to operating this equipment. If an owner/operator does not understand English, the contents of this manual shall be explained in the owner/ operator native language to assure the owner/operator comprehends. It is the owner/operator's responsibility to maintain the legibility of all warning and Instruction labels. The owner/operator shall retain this manual for future reference to important warnings, operating and maintenance instructions. Page 4 of 8 INSTALLATION See figures 1 & 2. Note: Arrow on oiler must point towards the valve Step 3 Assemble the air pressure gauge to the filter/regulator by first removing the plug on the side with the arrow pointing from left to right. Step 4 Assemble the filter/regulator to the oiler using (1) 1/4 NPT hex nipple. Note: Arrow on filter/regultor must point towards the valve Step 5 Fill the oiler with 30W non-detergent oil Note: Set to about 1/3 of max drip rate. Hose Barb #57 Air Gauge #008-370 Filter/Regulator #T17M Page 5 of 8 Oiler figure 1 Control valve Filter/Regulator Mounting holes Nipple #M25 figure 2 Oiler #T18 INSPECTION Prior to operation a visual Inspection shall be made. Any crusher that appears to be damaged in any way, is badly worn or operates abnormally shall be removed from use until repairs are made. If over pressurizing of the equipment is believed to have occurred, contact a factory authorized service center for inspection of the crusher. An annual inspection by a factory authorized service center is recommended. Verify the pressure gauge on the pressure regulator/filter reads between 100 and 120 p. s. i. [. . . ] MAINTENANCE Regularly check the pressure filter/regulator moisture trap for water. Regularly clean the crusher chamber to remove any accumulated sludge, metal particles or any other debris that could affect the crusher operation. Apply grease to door hinges on a regular basis to prevent the door from binding. [. . . ]