User manual HERCULES SMART TV SATELLITE

[. . . ] SYSTEM REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 HARDWARE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ENGLISH ESPAÑOL ITALIANO NEDERLAND DEUTSCH FRANÇAIS 2. 1. Installing the board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Once it is complete, the software prompts you to save the list of detected channels. - Give the list a name (the name of the satellite involved, for example) and click on OK. The control panel now displays the Program tab with the list of detected channels. - Repeat this procedure for the other LNBs (select a preset in the Select Dish field, select a satellite in the Satellite field and select an LNB in the LNB Setup field). You must assign a "path" to each satellite dish position for information transfer. As the LNB A path corresponds to the main position, we recommend that you assign it to LNB 1. - Click on LNB Setup in the LNB Setup 1 zone. If your satellite dish is only compatible with Mini-DiSEqC/Tone Burst: - Click on LNB Setup in the LNB Setup 1 zone. Your configuration should resemble the one in the illustration, opposite. - Select the Dish Setup tab. User Manual ­ 11/20 ESPAÑOL ITALIANO NEDERLAND DEUTSCH FRANÇAIS 5. 2. 4. Single LNB satellite dish, motorized ENGLISH - Select the Dish 1 preset in the Select Dish field. - Select the satellite corresponding to your dish's main position in the Satellite field. The satellite coordinates in the Degree field are updated automatically. Once it is complete, the software prompts you to save the list of detected channels. - Give the list a name (the name of the satellite involved, for example) and click on OK. The control panel now displays the Program tab with the list of detected channels. - Repeat this procedure for the other satellite dish positions (select a preset in the Select Dish field, select a satellite in the Satellite field and select a position in the LNB Setup field). 5. 2. 5. About USALS In addition to the DiSEqC 1. 2 protocol, the USALS protocol is also available. In fact USALS is not a distinct protocol as such, but rather an improvement on DiSEqC 1. 2; it consists of a software utility allowing the satellite dish to be aimed at a specific satellite without any adjustments. All you need to know are the coordinates of your place of residence (longitude and latitude), and satellite positions will be recalculated with respect to your location by USALS, which can aim the dish at a satellite with precision of one-tenth of one degree. USALS is mainly used in high-end satellite dish motors. 12/20 ­ User Manual 5. 3. Creating a Favorite List The procedure outlined above has enabled you to detect satellite channels, but with the vast number of channels available, you may well wish to keep only a selection of your favorites, accessible at any time. ENGLISH ESPAÑOL ITALIANO NEDERLAND DEUTSCH FRANÇAIS You must now select the channels to be included. Filters are available to help with your selection: media type (TV or Radio) and channel type (FTA (Free To Air), Scrambled or All). [. . . ] The information provided by this document is believed to be accurate and reliable. either for its use or for the infringement of patents or other rights of third parties resulting from its use. This product may exist in a light or special version for PC integration or other purposes. Certain functions detailed in this manual may not be available in these versions. [. . . ]