User manual HEAT AND GLO TIARAII-BR-B

[. . . ] Owner's Manual Installation and Operation TIARA I-B TIARA II-B DIRECT VENT ROOM HEATER Tested and Listed by O-T L C US Portland Oregon USA OMNI-Test Laboratories, Inc. Models: TIARAI-BK-B TIARAI-BR-B TIARAI-CTO TIARAI-CES TIARAII-BK-B TIARAII-BR-B TIARAII-CTO TIARAII-CES CAUTION DO NOT DISCARD THIS MANUAL · Important operating and · Read, understand and · Leave this manual with follow these instructions maintenance instructions party responsible for use for safe installation and included. operation. D DI O N SC O AR T D WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. · Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. · What to do if you smell gas - Do not try to light any appliance. [. . . ] Twist lock the high wind termination cap on to the top adapter. High Wind Termination Cap Step 10. Slide wall thimble cover over retro connector and secure with masonry bolts (Figure 5. 30). If you have a framed wall in front of the masonry, use wood screws to mount wall thimble cover to framed wall, over retro connector and 10 in. If needed, add a section of direct vent pipe to the retro connector in order to extend through the opening in the wall thimble cover. Top Adaptor (3) Sheet Metal Screws Retro Connector Wall Thimble Cover Flashing (4) Masonry Bolts (Not included) Figure 5. 28 Figure 5. 30 Step 9. Use three sheet metal screws to attach the flex liner to the connector (Figure 5. 29). Be careful to ensure that the connector is centered in the opening and the mounting holes line up with the masonry wall. Step 11. The connection between the appliance and the retro connector may be completed with sections of direct vent pipe. August 1, 2008 Heat & Glo · Tiara I B & Tiara II B · 7010-149M Page 23 A. Fuel Conversions Before making gas connections ensure that the appliance being installed is compatible with the available gas type. Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts. 6 Gas Information Tiara II-B Burner Removal: 1. Converting to LP Gas NOTE: Gas conversions should only be performed by a qualified service person, and/or where required by state and local codes, licensed installer/service technician. In the Commonwealth of Massachusetts, installation must be performed by a licensed plumber or gas fitter. KIT CONTENTS: Replacement orifice; replacement pilot injector; valve regulator; conversion label. TOOLS REQUIRED: Power drill (a 90° handle is helpful); #2 Phillips bit; 7/16" wrench, . open end wrench, Remove front (if installed), glass, and logs (if installed. ) Tiara I-B Burner Removal: Figure 6. 2 Using the #2 Phillips screwdriver remove the two (2) 1/4" x 20 screws securing the burner as indicated. Lift burner out of firebox. Figure 6. 1 Remove the optional brick set, if installed. Lift burner up and out of the firebox. Figure 6. 3 Remove the burner support by loosening the left screw on the pilot tower, and removing the three screws on the front side of the burner neck support. Slide the burner neck support to the left. Page 24 Heat & Glo · Tiara I B & Tiara II B · 7010-149M August 1, 2008 Tiara I-B and Tiara II-B: PILOT HOOD MILLIVOT GENERATOR THERMOCOUPLE Tiara I-B: Installation is the reverse of the removal. Reinstall logs, glass and front. Figure 6. 4 Pull off pilot hood and set aside. 2. Valve Regulator Replacement NOTE: Do not remove retaining clip from hood. WARNING 5/32 in. · Disconnect any electrical cords and turn off gas supply to unit before proceeding if converting fuel on an appliance already fully installed. Use a 5/32 in. Replace pilot injector with the one supplied with the appliance (#35 for Propane, #62 for Natural Gas). Replace pilot hood, snapping into position. Figure 6. 5 Remove upper and lower back shield. Remove the rods and adapter cap. 1 2 Mounting Screws Pressure Regulator Tower 3 Diaphragm Figure 6. 6 Remove main burner orifice using a 5/8 in. [. . . ] Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this warranty unless expressly authorized and approved by HEAT & GLO in writing. Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure, air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty. This warranty will be void if: a) The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer's Guide, Owner's Guide and Listing Agent Identification Label furnished with the Product. b) Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and approved by HEAT & GLO in writing. [. . . ]