User manual HATCO GR2SDM-0102

[. . . ] GLO-RAY GR2SD Series Installation & ® Designer Merchandising Warmer Operating Manual I&W # 07. 05. 078. 00 This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you are unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. [. . . ] GR2SDM-0102 8 SPECIFICATIONS DIMENSIONS - GR2SDS MODELS SLANT MODEL - DUAL SHELF Model GR2SDS-24D GR2SDS-30D GR2SDS-36D GR2SDS-42D GR2SDS-48D GR2SDS-54D GR2SDS-60D (A) Width 30-1/8" (77 cm) 36-1/8" (92 cm) 42-1/8" (107 cm) 48-1/8" (107 cm) 54-1/8" (138 cm) 60-1/8" (153 cm) 66-1/8" (168 cm) (B) Depth (C) Height (D) Height 26-5/8" (68 cm) 26-5/8" (68 cm) 26-5/8" (68 cm) 26-5/8" (68 cm) 26-5/8" (68 cm) 26-5/8" (68 cm) 26-5/8" (68 cm) 30-3/8" (77 cm) 30-3/8" (77 cm) 30-3/8" (77 cm) 30-3/8" (77 cm) 30-3/8" (77 cm) 30-3/8" (77 cm) 30-3/8" (77 cm) 8" (20 cm) 8" (20 cm) 8" (20 cm) 8" (20 cm) 8" (20 cm) 8" (20 cm) 8" (20 cm) Side View Front View A D D C B D D 9 Form No. GR2SDM-0102 INSTALLATION ALL MODELS Glo-Ray Designer Merchandising Warmers are shipped with most components pre-assembled. Care should be taken when unpacking shipping carton to avoid damage to unit and components enclosed. To prevent delay in obtaining warranty coverage, fill out and mail in the warranty card. To install them, simply place the bars in the channels provided (see Figure 4). The bars can be readily adjusted to separate your holding areas as needed. Figure 4. Installing Product Divider Bars LOCATION NOTE: The unit must be transported in the upright position. For proper operation and maximum performance, locate the Designer Merchandising Warmer in an area where the ambient air temperature is constant and is a minimum of 70° F (21° C). Areas which are susceptible to active air movements or currents should be avoided, i. e. , near exhaust fans or hoods and air conditioning ducts. WARNING For safe and proper operation, the unit must be located a reasonable distance form combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. CAUTION Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food. CAUTION The National Sanitation Foundation (NSF) requires that GR2SD Series units over 36" (91 cm) in length or weighing more than 80 lbs. If this unit cannot be sealed at the point of use, 4" (10 cm) legs are included to allow for proper cleaning access below unit. See Hatco ACCESSORIES for installation instructions. OPERATION The Designer Merchandising Warmer power is controlled by the ON/OFF toggle switch. The thermostatically controlled base can be set to any desired heating level as indicated on the control plate. NOTE: Main power switch must be in the ON position for the heated base to function. Use caution when touching these areas to avoid injury. OFF ON 80 F 28 C 200 F 93 C HATCO CORPORATION, Milwaukee, WI ON/OFF Toggle Switch Thermostat Control Figure 5. Controls WARNING Do not place food product directly onto hardcoat surface. GR2SDM-0102 10 MAINTENANCE GENERAL The Hatco Glo-Ray Designer Merchandising Warmers are designed for maximum durability and performance, with minimum maintenance. WARNING To avoid any injury, turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning. WARNING To avoid electrical shock or personal injury, do not steam clean or use excessive water on the unit. [. . . ] Hatco reserves the right to accept or reject any such claim in whole or in part. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer's sole expense. HATCO WILL NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER PRODUCT OR GOODS. 13 Form No. GR2SDM-0102 HATCO AUTHORIZED PARTS DISTRIBUTORS ALABAMA Jones McLeod Appl. [. . . ]