User manual HATCO DHLM-0105

[. . . ] Decorative Heat Lamps DL Series Installation & Operating Manual I&W #07. 05. 147. 00 This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you're unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. [. . . ] DHLM-0105 6 INSTALLATION INSTALLING NON-TRACK MOUNT (A, C, P, S AND R) (See Figure 6) WARNING To avoid any injury, turn the power supply OFF to the electrical junction box before mounting. Mount the top bracket to the 4" (102 mm) octagon junction box using the two screws provided with the junction box. Making sure all power is OFF, connect supply lead L1 to the black lamp lead, connect neutral to the white lamp lead, If lamp is equipped with three wires, connect ground to the green lead. If lamp is equipped with two wires, make proper ground wire connections from junction box. Slide the canopy cover or cord housing up until it rests against the ceiling and install the two ball cap-nuts until snug to the ceiling. A, C, P & S Mount INSTALLING TRACK MOUNT (CT, ST AND RT) CAUTION Hatco DL lamp warmers are built to fit HALO brand L651, L652 and L653 Power Trac, track lighting systems only. CAUTION For safe and proper operation the maximum capacity of Power-Trac is 20A per circuit. 20A maximum includes all lights and appliances connected to the circuit. The Trac system is to be supplied by a single branch circuit 120V, 60 Hz, 20A. NOTE: Maximum seven 250 watt lamp units or five 375 watt lamp units per each 20 amp Track Bar circuit. Installer is responsible for properly sizing the supply circuit with the lamp load. Hatco provides track kits in three different lengths: · L651 - 4 ft. When installing or using this Trac system, the 7 R Mount Figure 6. Non-Track Mounting following basic safety precautions should always be followed: · · Read all of these installation instructions before installing the Trac system. Save these instructions and refer to them when additions to or changes in the Trac configuration are made. Do not install any part of a Trac system less than 5 feet (1524 mm) above the floor. Do not install any fixture assembly closer than 1" (25 mm) along the sides from any curtain or similar combustible material. Disconnect electrical power before adding to or changing the configuration of the Trac. Do not attempt to energize anything other than Trac lighting fixtures on the Trac. To reduce the risk of fire and electric shock, do not attempt to connect power tools, extension cords, appliances, etc. DHLM-0105 · · · · · INSTALLATION CAUTION For safe and proper operation do not use Trac system units with a power supply cord or convenience receptacle adapter. CAUTION To reduce the risk of fire and electric shock when installing Trac systems, use only fixture assemblies marked for use with Halo Trac, and Trac Fittings marked for use with L650 Series Trac. The mounting clips, screws or stems are to be mounted in pre-drilled holes as follows: · · · · 2 foot (610 mm) Trac-two places, one at each end of Trac. [. . . ] Hatco reserves the right to accept or reject any such claim in whole or in part. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer's sole expense. HATCO WILL NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER PRODUCT OR GOODS. Form No. DHLM-0105 HATCO AUTHORIZED PARTS DISTRIBUTORS ALABAMA Jones McLeod Appl. [. . . ]