User manual HASSELBLAD FLEXBODY

[. . . ] Transparency Holder Guide: all transparency holders fit between two rails to keep them straight. Original Holder Clasp: all original holders slide into a slot here and are held in place by a magnetic clasp. The switch can light up in 3 different colors indicating the following: Green (Power/Ready) - remains lit when ready to scan. Flashes when first installed to indicate that firmware must be loaded (it will be loaded automatically when you run FlexColor). [. . . ] Connect a FireWire cable from one of the FireWire connectors on your scanner (see "Back Panel & Connectors" on page 10) to either the computer's FireWire connector or to a free FireWire connector on any other FireWire device already connected to your computer. Connect the round connector from your power supply to the round power supply socket on the back of the scanner. IMPORTANT: Make sure that the wall socket you are planning to use meets the electrical requirements outlined earlier. Note that the power supply may emit a low buzzing sound when plugged in. Turn on your computer and install the FlexColor image scanning software. 3. 6. User's Guide - Flextight 646 English 1. Place the scanner on a table near your computer with the front facing away from you. Make sure that the location you choose meets all environmental - and electrical requirements as described on page 11. 14 Hardware Reference - Flextight 646 Setting up the Scanner Attaching/Detaching the Feed Table English C B D A D Figure 4: Attaching/Detaching the Feed Table To attach the feed table correctly onto the scanner lead the brackets (B) as far as they go into the slits (C) in the scanner base, then lower the table and pull it slightly backwards to ensure that the notches (D) catch the bottom of the slits. To detach the feed table correctly from the scanner lift it slightly upwards to release the notches (D) from the bottom of the slits (C) then pull it away from the scanner. User's Guide - Flextight 646 Hardware Reference - Flextight 646 Setting up the Scanner 15 Mounting/Dismounting of the Cabinet A B C Figure 5: Mounting/Dismounting of the Cabinet To dismount the cabinet (A) remove the two screws (B) at the scanner back using a 2. 5 mm allen key, then pull the cabinet upwards. When mounting the cabinet, make sure that it catches the bends (C) in both sides, then lower it slowly while making sure that it goes free of all cables and extrusions and finally tighten the screws (B). User's Guide - Flextight 646 English 16 Hardware Reference - Flextight 646 Operating the Scanner English A B C FLEX TIG HT E F à OR IGIN AL HO LD ER PATE NT PE ND ING D à J K G H L M Figure 6: Operating the Flextight 646 scanner User's Guide - Flextight 646 Hardware Reference - Flextight 646 Operating the Scanner 17 Operating the Scanner (See Figure 6 opposite). It is assumed that the scanner and FlexColor software have been properly installed. Make sure that the feed table (A) has been attached properly onto the scanner (see "Attaching/Detaching the Feed Table" on page 14). 1. 10 2. Load the sheet into the 6 x 6 original holder with the lines pointing towards the scanner (vertically). Use the scanner's light table grid and the corners marked on the sheet to help align it. 5. Click on the Calibrate button, and the focus calibration starts. When the focus calibration is finalized, the focus calibration window closes again. Your scanner is now calibrated for all resolutions and for both transparent and reflective originals. User's Guide - Flextight 646 English 22 Hardware Reference - Flextight 646 Calibrating the Scanner White Calibration for Reflectives The Flextight scanner uses a white reference to make sure that all elements in the scanner's CCD react consistently to light brightnesses. The scanner has been calibrated from the factory, and the calibration data is stored in the scanner's flash PROM. As the scanner ages, the properties of the light tubes may change slightly. Therefore, you must redo the white calibration every six months or so and immediately after changing the light tubes. It is a square white piece of paper (219 x 219 mm (8. 6" x 8. 6")). If you have lost the white calibration sheet, then you can use a flat (non-textured), perfectly white piece of paper of the same dimensions. If you have used the reflective holder before, make sure that there are no finger prints or other marks on the plastic layer. (Please note that the A4/letter-size reflective holder in not included in the standard delivery). [. . . ] 60 W during operation Power Requirements 100-240V AC, 1. 3A, 50-60Hz Interface to Computer FireWire (IEEE 1394) Front Panel One multifunction switch (on/off switch) with integrated status light Drum Force 1kg (2. 2lbs) Operating Environment Operating Temperature: 10 - 35°C (50 - 95°F) Recommended Working Temperature: 10 - 25°C (50 - 77°F) Humidity: 20 - 80% RH (no condensation) Storage Environment Temperature: 0 - 50°C (32 - 122°F) Relative humidity: 20 - 80% RH (no condensation) Originals Transparencies: from 35mm to 4x5 inches, <1mm thick Reflectives: up to 220 x 310mm (A4 oversize), <1mm thick Lamp type Color optimized fluorescent lamp Dimensions Height: 650 mm (25. 6") Width: 390 mm (15. 4") Depth: 230 mm (9. 1") (excl. feed table) Weight 17 kg (38 lbs) User's Guide - Flextight 646 Hardware Reference - Flextight 646 FCC Notice 29 FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ]