User manual HASBRO ZOIDS SHADOW FOX 83147100

[. . . ] NÄR DENNA DEL ÄR ÖPPNAD OCH UND VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNETAUSSETZEN. NICHT DEM STRAHL OHITETTAESSA LASERSTRÅLING ADVARSEL USYNLIGFUNKTION. ÄLÄ KATSO UDE AF UDSAETTELSE FOR STRÅLING. CLASS 1 LASER PRODUCT LASER KLASSE 1 Caution This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of the product. [. . . ] (A) Open the feeding roller cover and pull the original gently to the left and out from the original feeder tray. Open and close the original cover to clear the SPF misfeed ( ) indicator. If the misfed original cannot be easily removed, proceed to (C). Feeding roller cover 34 (B) Open the original cover and rotate the roller rotating knob to remove the misfed original from the exit area. If the misfed original cannot be easily removed, proceed to (C). Roller rotating knob (C) If the original does not move easily into the exit area, remove it in the direction of the arrow while rotating the knob. A number may appear in the display after a minus sign, indicating the number of the originals that must be returned to the original feeder tray. ) indicator and Open and close the SPF to clear the SPF misfeed ( then clear the misfeed and return the required number of originals. Then press the start ( ) key to resume copying. 6 DEVELOPER REQUIRED When the developer replacement required ( ) indicator lights up, the developer should be replaced. DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN AUTORIZED HASBRO SERVICE TECHNICIAN. Contact your service centre as soon as possible. MAINTENANCE REQUIRED When maintenance ( ) indicator lights up, service by an authorised HASBRO service technician is required. Contact your service centre as soon as possible. 35 SCAN HEAD LOCKING SWITCH The scan head locking switch is under the original table. ), Grasp here and turn in the direction of the arrow. Lock Unlock 36 7 OPTIONAL EQUIPMENT (AL-12PKM) The procedure for installing the software for the optional Printer/Scanner Expansion Kit (AL-12PKM) and the operation of the printer/scanner is explained here. For the procedure for installing the AL-12PKM, see the setup guide that accompanies the AL-12PKM. (Normally, the correct language is selected automatically. ) 4 Select the software packages to be installed, and then click the "Next" button. The software packages with checkmark ( ) on the list on the screen will be installed. Click the "Display README" button to show the information on the selected package. 40 · If you are using the parallel interface connection, do not select the Button Manager checkbox because this feature is not supported with the parallel interface. · If the following screen appears, click the "OK" button. Review the contents in "BEFORE INSTALLATION" (p. 38), and then select only appropriate the software packages to be installed. 5 Review the software packages to be installed on the screen, and then click the "Start" button. The software packages to be installed will be displayed on the screen. If inappropriate packages are displayed, click the "Back" button to select appropriate packages again. 6 Copying files for MFP driver installation and parallel interface setup (This step will start if it was selected in step 4). 1 2 3 4 After confirming the message in the "Welcome" window, click the "Next" button. A dialog box appears asking you to verify that the USB or parallel interface cable is not connected to the MFP. Make sure that the interface cable is not connected and click the "Next" button. Click the "Next" button in the dialog box to install the MFP driver or Cancel to quit the installation. If the following screen appears while the files are being copied (the message may appear more than once), click "Continue Anyway". When the "The MFP driver installation is complete. " dialog box appears, click the "OK" button. The Button Manager installer will start. 7 41 7 Begin installation of the Button Manager (This step will start if it was selected in step 4). 1 2 3 4 5 After confirming the message in the "Welcome" window, click the "Next" button. [. . . ] Government End Users. If you are acquiring the Software on behalf of any unit or agency of the United States Government, the following provisions apply. The Government agrees: (i) if the Software is supplied to the Department of Defense (DoD), the Software is classified as "Commercial Computer Software" and the Government is acquiring only "restricted rights" in the Software and its documentation as that term is defined in Clause 252. 227-7013 (c)(1) (Oct. 1988) of the DFARS; and (ii) if the Software is supplied to any unit or agency of the United States Government other than DoD, the Government's rights in the Software and its documentation will be as defined in Clause 52. 22719 (c)(2) of the FAR or, in the case of NASA, in Clause 18-52. 227-86 (d) of the NASA Supplement to the FAR. 75 6. Limited Warranty on Media. HASBRO warrants the disks on which the Software is recorded to be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced by a copy of the receipt. [. . . ]