User manual HASBRO ZOIDS PTERAMANDER

[. . . ] NÄR DENNA DEL ÄR ÖPPNAD OCH UND VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNETAUSSETZEN. NICHT DEM STRAHL AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER ADVARSEL UDE AF FUNKTION. ÄLÄ KATSO SÄTEESEEN. Caution This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of the product. [. . . ] The interface cable should be connected during installation of the MFP driver. (p. 22) Connecting the USB interface cable 1 2 Obtain a shielded USB interface cable. Insert the cable into the USB interface connector located on the rear of the unit. 4 3 Insert the other end of the cable into the interface connector of your computer, or the USB hub connected to your computer. Connecting the parallel interface cable 1 2 3 Obtain an IEEE1284 shielded parallel interface cable. Insert the cable into the parallel interface connector located on the rear of the unit, and fasten with clasps. 4 Insert the other end of the cable into the interface connector of your computer. 45 5 MAKING COPIES This chapter explains basic and other copying functions. This memory allows the unit to scan an original once only and make up to 99 copies. This feature improves workflow, reduces operation noise from the copier, and provides higher reliability by reducing wear and tear on the scanning mechanism. If the unit does not function properly during use, or if a function cannot be used, see "TROUBLESHOOTING THE UNIT" (p. 61). COPY FLOW 1 Make sure that paper has been loaded in the paper tray (p. 15) or multi-bypass tray (p. 17), and check the paper size (p. 14). If paper is not loaded, see page 15. If you are using the single bypass, check the paper size and then proceed to the next step without loading paper. 2 Place the original. If you are using the original table, see "Using the original table" (p. 47). When copying onto paper larger than A4, pull out the paper output tray extension. 3 Select the copy settings. If you wish to copy using the initial settings (p. 13), proceed to the next step. (ZOIDS PTERAMANDER, AL-1555) To print on both sides of the paper, see page 52. 4 Start copying. Press the start ( ) key. If you are using the single bypass Do not press the start ( ) key. (Page 18) Multiple copies are not possible using the single bypass. 46 Do not insert paper in the single bypass when a copy job from the paper tray is in progress. Adjust the original guides to the size of originals. 3 Set the originals face up in the original feeder tray. Original face up 48 Stream feeding mode The stream feeding mode allows easy operation of continuous copying from the SPF/ RSPF. If the stream feeding mode has been enabled using user program No. 4, the SPF/RSPF ( ) indicator will blink approximately 5 seconds after the last original has been fed by the SPF/RSPF. While this indicator is blinking, any new originals placed in the original feeder tray will be fed and copied automatically. If the stream feeding mode has been disabled, the start ( ) key must be pressed each time the originals are set even immediately after completion of a copy run from the SPF/RSPF. See "USER PROGRAMS" (p. 55). SET THE COPY QUANTITY Set the number of copies using the two copy quantity ( from the original table or copying from SPF/RSPF. , ) keys when copying · Press the clear ( ) key to clear an entry if a mistake is made. · A single copy can be made with the initial setting, i. e. , when "0" is displayed. · Press the right copy quantity key to set the unit digit from 0 to 9. · Press the left copy quantity key to set the tens digit from 1 to 9. Tens digit Unit digit 5 EXPOSURE ADJUSTMENT/PHOTO COPYING Exposure adjustment Copy density adjustment is not required for most originals in the automatic exposure mode. To adjust the copy density manually or to copy photographs, the exposure level can be adjusted in two steps manually. (p. 55) ) mode can be 1 Press the exposure mode selector key to select the MANUAL ( ) mode or PHOTO ( ) mode. 2 Use the light ( ) and dark ( ) keys to adjust the exposure level. [. . . ] References IARC(1996) : IARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. 65, Printing Process And Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp. 149-261 H. Muhle, B. Bellmann, O. Creutzenberg, C. Dasenbrock, H. Ernst, R. Kilpper, J. C. MacKenzie, P. Morrow, U. Mohr, S. Takenaka, and R. Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats. The information on this data sheet represents our current data and best opinion as to the proper use in handling of this product under normal conditions. However, all materials may present unknown hazards and should be used with caution. [. . . ]