User manual HASBRO ZOIDS LIGER ZERO

[. . . ] · When moving the unit, be sure to turn the power switch off and remove the power cord from the outlet. · Do not cover the unit with a dust cover, cloth or plastic film while the power is on. · Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. · The socket-outlet shall be installed near the unit and shall be easily accessible. Important points when selecting an installation site Do not install your unit in areas that are: · damp, humid, or very dusty · exposed to direct sunlight · poorly ventilated · subject to extreme temperature or humidity changes, e. g. , near an air conditioner or heater. [. . . ] For the change of the printer port setting, see "USING OTHER INSTALLED DRIVERS" (p. 66). 41 Flow of installation Refer to the following table and then begin installation. Operating system Windows XP Windows 98 Interface USB/ Parallel USB Parallel USB Windows Me Parallel USB Windows 2000 Windows 95/ NT 4. 0 Parallel Parallel Reference pages for how to install Installing onto Windows XP (USB/parallel interface) (p. 43) Installing onto Windows 98/Me/2000 (USB interface) (p. 47) Installing onto Windows 95/98/Me/NT4. 0/2000 (Parallel interface) (p. 50) Installing onto Windows 98/Me/2000 (USB interface) (p. 47) Installing onto Windows 95/98/Me/NT4. 0/2000 (Parallel interface) (p. 50) Installing onto Windows 98/Me/2000 (USB interface) (p. 47) Installing onto Windows 95/98/Me/NT4. 0/2000 (Parallel interface) (p. 50) Installing onto Windows 95/98/Me/NT4. 0/2000 (Parallel interface) (p. 50) 42 INSTALLING THE SOFTWARE The following term is used in this section. MFP Means the unit as a printer and scanner. · For this description, it is assumed that the mouse is configured for right hand operation. · The scanner feature only works when using a USB interface cable. · If any error message appears, solve the problem following the instructions on the screen. After your problem is solved, the installing procedure will be continued. In this case, click the "Cancel" button to exit the installer. After solving your problem, reinstall the software from the beginning. Installing onto Windows XP (USB/parallel interface) Before starting the installation, make sure the USB or parallel interface cable is not connected to the MFP. 1 2 Insert the supplied CD-ROM into your CD-ROM drive. Click the "start" button, click "My Computer" ( double-click the CD-ROM ( ) icon. ), and then When any of "Found New Hardware Wizard" messages appear during the software installation, be sure to click the "Cancel" button. 3 Double-click the "setup" ( ) icon. If the language selection screen appears after you double click the "setup" icon, select the language you wish to use and click the "Next" button. (Normally, the correct language is selected automatically. ) 4 Select the software packages to be installed, and then click the "Next" button. The software packages with checkmark ( ) on the list on the screen will be installed. If you are using Windows XP with the parallel interface, go to step 12. Begin installation of the scanner driver. 1 2 3 "HASBRO AR-xxxx" (where xxxx is the model name of your MFP) will appear in the "Found New Hardware Wizard" dialog box. Select "Install the software automatically (Recommended)" and click the "Next" button. When installation of the driver is completed, click the "Finish" button to finish the scanner driver installation. 12 Begin installation of the printer driver. "HASBRO AR-xxxx" (where xxxx is the model name of your MFP) will appear in the "Found New Hardware Wizard" dialog box. Select "Install the software automatically (Recommended)" and click the "Next" button. 3 When installation of the driver is completed, click the "Finish" button to finish the printer driver installation. You have completed the installation of all the software. 1 46 Installing onto Windows 98/Me/2000 (USB interface) Before starting the installation, make sure the USB interface cable is not connected to the MFP. 1 2 Insert the supplied CD-ROM into your CD-ROM drive. ), and then double-click the When any of "Hardware Found", or "Found New Hardware Wizard" messages appear during the software installation, be sure to click the "Cancel" button. 3 Double-click the "setup" ( ) icon. If the language selection screen appears after you double click the "setup" icon, select the language you wish to use and click the "Next" button. (Normally, the correct language is selected automatically. ) 4 Select the software packages to be installed, and then click the "Next" button. The software packages with checkmark ( ) on the list on the screen will be installed. Click the "Display README" button to show the information on the selected package. If the following screen appears, click the "OK" button. Review the contents in "BEFORE INSTALLATION" (p. 41), and then select the appropriate driver software packages to be installed. 8 5 Review the software packages to be installed on the screen, and then click the "Start" button. The software packages to be installed will be displayed on the screen. If inappropriate packages are displayed, click the "Back" button to select appropriate packages again. 47 6 Copying files for MFP driver installation. 1 2 3 4 After confirming the message in the "Welcome" window, click the "Next" button. [. . . ] While there have been no studies to date using developer, a two-year cancer bioassay using a typical toner preparation containing carbon black (a small amount of toner is included in the developer mixture) demonstrated no association between toner exposure and tumor development in rats. Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any non-toxic dust. Medical Conditions Generally Aggravated by Exposure: None Emergency and First Aid Procedures: Inhalation; Remove to fresh air. Eye; In case of contact, immediately flush eyes with water for 15 minutes. Route(s) of Entry: Section 6. Physical Chemical Characteristics Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Specific Gravity: Solubility in Water: PH: Viscosity: Color: about 7. 3 Negligible Not applicable Not applicable Black Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Fire and Explosion Data Not applicable >350¡C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards. [. . . ]