User manual HASBRO ZOIDS ENERGY LIGER

[. . . ] For the procedures for using the software programs, see the user's guides on the CD-ROM. * Memory can be added by installing a commercially available 128 MB or 256 MB memory module (144-pin SDRAM SODIMM). This manual only explains features that can be used when the Network Scanner Expansion Kit is installed. For information on loading paper, replacing toner cartridges, clearing paper misfeeds, handling peripheral devices, and other copier-related information, please refer to your operation manual for copier. [. . . ] (p. 30) ADDRESS BOOK ADDRESS REVIEW ADDRESS ENTRY SEND SETTINGS If the send settings are not changed, a file name is assigned based on the items specified in the Web page. 11 If you have another page to scan, change pages and then press the [START] key ( ). Repeat this sequence until all pages have been scanned. Note When sending an image by Scan to E-mail, a subject and sender's name can be entered. Normally the subject and sender are automatically entered based on the information stored in "Reply E-mail Address" in "SMTP Setup" in the Web page. If user authentication is enabled, the e-mail address of the user who logged in is used as the sender. Note If no action is taken for one minute, scanning automatically ends and transmission begins. 12 After the final page is scanned, touch the [READ-END] key. "SENDING. PRESS [C] TO CANCEL. " appears in the touch panel and transmission begins. When transmission is finished, "SENDING COMPLETED. " appears in the touch panel. ESS [START]. EAD-END]. READ-END Note To cancel transmission while "SCANNING ORIGINAL. " appears in the display or before the [READ-END] key is touched, press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ). If you press the [CLEAR] key ( ), the destination and scan settings are saved. To cancel a transmission, press the [JOB STATUS] key and cancel the job. (p. 31) If you exceed the number of pages that can be scanned while scanning an original, "THE MEMORY BECOMES FULL. " will appear in the touch panel. To send the data that has been scanned to that point, touch the [SEND] key. If a misfeed occurs while an original is being scanned, remove the original according to the instructions in the touch panel. (p. 20) Touch the [ORIGINAL] key. 300dpi RESOLUTION 4 Touch the [OK] key. OK INAL SIZE MANUAL You will return to the initial screen. 2-SIDED TABLET JOB BUILD ROTATE THE IMAGE 90 DEGREES TIFF-G4 FILE FORMAT AUTO 8X11 ORIGINAL A two-sided original icon appears next to the [ORIGINAL] key. (Example: The icon that appears when the [2-SIDED BOOKLET] key is touched. ) QUALITY 300dpi RESOLUTION TIFF-G4 FILE FORMAT AUTO 8X11 ORIGINAL 3 Touch the [2-SIDED BOOKLET] key or the [2-SIDED TABLET] key as appropriate for the original you loaded. ORIGINAL SIZE AUTO MANUAL 2-SIDED BOOKLET 2-SIDED TABLET ROTATE THE If you wish to rotate the original 90 when creating an image file, touch the [ROTATE THE IMAGE 90 DEGREES] checkbox (a checkmark should appear in the box). 5 Continue from step 4 of "BASIC TRANSMISSION METHOD" (p. 20 to 21). Note If the correct original size does not appear in the screen of step 2, touch the [MANUAL] key and specify the correct original size (p. 26). Note Booklets and tablets Two-sided originals that are bound at the side are booklets, and two-sided originals that are bound at the top are tablets. Two-sided scanning mode can also be canceled by pressing the [CLEAR ALL] key ( ). Booklet Tablet 24 HOW TO USE THE NETWORK SCANNER FUNCTION SCANNING A LARGE NUMBER OF ORIGINALS (when an RSPF is installed) If you have a large number of originals, the originals can be scanned in batches using the RSPF. 1 2 Make sure the machine is in scanner mode and then load the document in the RSPF. (p. 20) Touch the [ORIGINAL] key. 300dpi RESOLUTION 5 6 Perform steps 4 through 9 of "BASIC TRANSMISSION METHOD". (p. 20 to 21) Press the [START] key ( ). TIFF-G4 FILE FORMAT AUTO 8X11 ORIGINAL Scanning of the originals begins. A message appears in the touch panel. 2 7 When all of the originals in the RSPF have been scanned, load the next batch and press the [START] key ( ). Repeat this sequence until all pages have been scanned. OK 3 Touch the [JOB BUILD] key. If you wish to rotate the original 90 when creating an image file, touch the [ROTATE THE IMAGE 90 DEGREES] checkbox (a checkmark should appear in the box). RIGINAL SIZE MANUAL 2-SIDED TABLET JOB BUILD Note If no action is taken for one minute, scanning automatically ends and transmission begins. ROTATE THE IMAGE 90 DEGREES Note If the correct original size does not appear in the screen of step 2, touch the [MANUAL] key and specify the correct original size (p. 26). 8 When all originals have been scanned, touch the [READ-END] key. "SENDING. PRESS [C] TO CANCEL. " appears in the touch panel and transmission begins. When transmission is finished, "SENDING COMPLETED. " appears in the touch panel. 4 Touch the [OK] key. OK ESS [START]. EAD-END]. NAL SIZE MANUAL 2-SIDED TABLET You will return to the initial screen. READ-END JOB BUILD ROTATE THE IMAGE 90 DEGREES A job build icon appears next to the [ORIGINAL] key. QUALITY 300dpi RESOLUTION TIFF-G4 FILE FORMAT AUTO 8X11 ORIGINAL Note Job build mode turns off after transmission is finished. Job build mode can also be canceled by pressing the [CLEAR ALL] key ( ). When performing Scan to E-mail, see the notes on page 22. 25 SCANNING SETTINGS (ORIGINAL SIZE, QUALITY, RESOLUTION, FILE FORMAT, AND SEND SETTING) When sending an image, you can change the original scan size, quality, resolution, file format, and file name. MANUALLY SETTING THE SCANNING SIZE If you load an original that is not a standard size, or if you wish to change the scanning size, touch the [ORIGINAL] key and set the original size manually. [. . . ] Store a metadata set in the Web pages and then perform the transmission procedure. 2 Touch the key of the metadata that you wish to use. CANCEL METADATA 2 METADATA 4 METADATA 6 METADATA 8 OK If the entry values of the metadata item were stored in selection format, the selections will appear as keys. If a value is editable, the [DIRECT ENTRY] key can be touched to manually enter a value. If a metadata item requires the entry of text, a text entry screen will appear. Enter the required information. 4 Note 1/2 To change the number of items that appear at once, touch the display item number select key. [. . . ]