User manual HASBRO YAHTZEE 2003

[. . . ] If your copier is so marked, please read "I" for "ON" and " " for "OFF". The socket-outlet shall be installed near the equipment and shall be easily accessible. Required in IEC-950 (EN 60 950) - Europe The equipment should be installed near an accessible socket outlet for easy disconnection. Required in Appendix ZB of BS 7002 (En 60 950) -- United Kingdom MAINS PLUG WIRING INSTRUCTIONS The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. Always refit the fuse cover after replacing the fuse on the moulded plug. [. . . ] To cancel the margin shift function, touch the [CANCEL] key on the margin shift setting screen. 2 Select the shift direction. Touch a shift direction key to select right or left. The selected key will be highlighted. RIGHT LEFT 5-3 SPECIAL MODES Erase The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The erase width is approximately 10 mm (1/2") in it's initial setting. NOTE The initial setting for the erasure width can be changed in the key operator programs to any value from 0 to 20 mm (0 to 1"). (Page 15 of the Key operator's guide) Original Copy EDGE ERASE Eliminates shadow lines around the edges of copies caused when heavy paper or a book is used as an original. CENTRE ERASE Eliminates shadow lines produced by the bindings of bound documents. EDGE + CENTRE ERASE Eliminates shadow lines around the edges of copies and eliminates the shadow at the centre of copies. To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 3 Adjust the amount of erase and touch the [OK] key. CANCEL EDGE OK 1 MODES Touch the [ERASE] key on the special modes screen. DUAL C TAN C 10 (0 mm 20) RGIN SHIFT ERASE PHLET COPY JOB BUILD The erase setting screen will appear. The erase icon ( ) will also appear in the upper left of the screen to indicate that the function is turned on. Use the and keys to set the erase width to any value from 0 to 10 mm in 1 mm increments (0" to 1" in increments of 1/8"). 4 Touch the [OK] key on the special modes screen. You will return to the main screen of copy mode. About the steps that follow If an automatic document feeder is being used, see pages 4-7 through 4-10. NOTE When erase is used, edge erase takes place at the edges of the original image. If you also use a ratio setting, the edge erase width will change according to the set ratio. To cancel the erase function, touch the [CANCEL] key on the erase setting screen (step3). 2 Select the desired erase mode. ERASE EDGE ERASE CENTRE ERASE EDGE+CENTRE ERASE Select one of the three erase modes. (In the screen example, the " TRAY2" display is the tray selection key. ) The tray selection screen appears when the tray selection key is touched. NOTES G Two-sided copying is not possible on label sheets, and transparency film. When copying on a cover, do not select a tray that has one of these types of paper. G Select the same size of paper for the covers as for the copies. 12 [When using feeder:] the automatic document Copying will start after all originals have been scanned. (The next step is not needed. ) [When using the document glass:] Replace the original with the next original and press the [START] key. Repeat this operation until all originals have been scanned and then touch the [READ-END] key. NOTES G When the pamphlet copy function is set, the twosided copying mode will be automatically selected. G If this function is used in combination with the pamphlet copy function (pamphlet stapling) and the number of original pages exceeds the number of pages that can be stapled, a message asking you to select "CANCEL", "CONTINUE", or "DIVIDE" will appear. To make pamphlet copies without stapling, select "CONTINUE". To divide the pages into sets that can be stapled, select "DIVIDE". If you performed steps 4 to 6 to insert cover paper, divided stapling is not possible. [. . . ] 1-11, 3-14 Saddle stitch tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18 8-7 INDEX Top tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5, 3-7 Total count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 Total number of originals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]