User manual HASBRO XEVOZ SKULL JACK UNNATURAL

[. . . ] This manual explains the changes to those procedures when the data security kit is installed. When the data security kit is installed When the data security kit is installed, the following icon appears on the touch panel. Touch the icon ( ) to view information on the data security kit version. When the data security kit is installed, data remaining in the machine is automatically erased after each copy and fax job. [. . . ] Press the [USER NAME] key to enter your user name and the [PASSWORD] key to enter your password. When you have finished entering your user name/password, touch the [OK] key. After entering your user name and password, continue from step 4 on page 5-8 of the "OPERATION MANUAL (for printer)". Among the administrator settings used by the administrator for the data security kit, this section explains the settings that are related to the security function. When the data security kit is installed, entry of the administrator password will be prohibited for 5 minutes if an incorrect administrator password is entered 3 times in a row. When the data security kit is installed, settings related to security (with the exception of [SSL SETTINGS] and [ENABLE IPsec]) are added to the settings that appear when the [SECURITY SETTINGS] key is touched. Touch the key in the lower right corner of the screen to move to the next screen. This setting is used to manually clear all data from the memory of the machine. Note, however, that the following types of data are not cleared with this setting. Use the "CLEAR ADDRESS BOOK DATA/IMAGE SEND REGISTERED DATA" setting on page 7 to clear the following types of data INDIVIDUAL/GROUP/PROGRAM/RELAY BROADCAST MEMORY BOX* SENDER CONTROL LIST POLLING MEMORY/CONFIDENTIAL MEMORY BOX* SENDER DATA ALLOW/REJECT RECEPTION SETTING DATA (INCLUDING POLLING PASSCODE NUMBER) FORWARD INFORMATION * The image data stored in the MEMORY BOX is cleared to execute this setting (CLEAR ALL MEMORY). NOTE In the event that the data security kit or the machine with the data security kit installed will be disposed of or ownership will change, the administrator should be sure to run this setting. NOTE When there is a stored image send job (fax, or network scanner)*, automatic clearing will not take place when the power is turned on. * This includes received faxes that have not yet been printed; however, it does not include data in a fax memory box (except confidential memory box). If you wish to cancel after data clearing has begun See the explanations in "Clear screen 2" and "If you wish to cancel after data clearing has begun" in "CLEAR ALL MEMORY" on page 6 of this manual. The number of times "POWER UP AUTO CLEAR" is repeated can be set to any number from 1 to 7. Touch the [NUMBER OF TIMES POWER UP AUTO CLEAR PROGRAM IS REPEATED] key, and set the desired number of times with the or key. ) NOTE This setting is only enabled when the "POWER UP AUTO CLEAR" checkbox is selected. The number of times auto clear is repeated after each job is printed or transmitted can be set to any number from 1 to 7. Touch the [NUMBER OF TIMES AUTO CLEAR AT JOB END PROGRAM IS REPEATED] key, and set the desired number of times with the or key. About the repeat setting When the repeat setting (number of repetitions) is increased to enhance the security function, the time required for data clearing increases. It is recommended that you select repeat settings for "NUMBER OF TIMES DATA CLEAR IS REPEATED", "NUMBER OF TIMES POWER UP AUTO CLEAR PROGRAM IS REPEATED", and "NUMBER OF TIMES AUTO CLEAR AT JOB END PROGRAM IS REPEATED" that are suitable for your security needs and conditions of use. This program can be used to prohibit the storage of print jobs that are not protected by a pass code when the print hold job function of print mode is used. [. . . ] "ALL CUSTOM SETTING LIST", "SENDING ADDRESS LIST", "SENDER CONTROL LIST" Select the checkboxes of the lists for which you wish to disable printing and then touch the [OK] key. This setting is used to select whether or not the job list that appears when "COMPLETE" is selected in the job status screen is displayed (page 1-15 of the "OPERATION MANUAL (for general information and copier operation)"). (The setting can be selected separately for "PRINT JOB" , "SCAN TO" , and "FAX JOB" modes. ) The JOBS COMPLETED list stores and displays printer mode user names, fax/image send destinations, and received fax sender information. [. . . ]