User manual HASBRO WORDSTERS

[. . . ] Dieses Gerät entspricht den Anforderungen der EU-Richtlinien 98/13/EU und 89/336/EWG sowie 73/23/EWG, die durch die Richtlinie 93/68/EWG geändert wurden. Cet appareil est conforme aux exigences de la directive 98/13/CEE ainsi que des directives 89/336/CEE et 73/23/ CEE modifiées par la directive 93/68/CEE. Este aparato satisface las exigencias de las Directivas 98/13/CE y 89/336/CEE, 73/23/CEE modificadas ambas por medio de la 93/68/CEE. Quest'apparecchio è conforme ai requisiti delle direttive 98/13/CE e 89/336/EEC, 73/23/EEC, entrambe emendate dalla 93/68/EEC. [. . . ] SETTINGS FUNCTION 0 2 Press these keys: The display will show: OVERRIDE CODE 3 4 50 Enter a 3-digit code number by pressing the number keys. 5 5 4 (Example) STOP Press the START/MEMORY key and then the STOP key. START/ MEMORY all-UX84H. book Page 51 Wednesday, July 5, 2000 8:48 AM Override Ringing Overriding the answering machine 2. Answering Machine Your callers should follow the steps below to override the answering machine. 1 Your caller calls the UX-84 from a tone dial telephone. When the outgoing message begins, they should press the "#" key on their telephone. · The caller will hear a short beep, and the outgoing message will stop. 2 The caller should enter the override code and "#" by pressing the appropriate keys on their telephone. · If an incorrect code is entered, the caller will hear four beeps. He or she must re-enter the correct code within 10 seconds or the line will be disconnected. 5 5 4 (Example) 3 The UX-84 will make a special ringing sound. · If you do not answer within 30 seconds, the outgoing message will play again and the caller can then leave a message. 51 all-UX84H. book Page 52 Wednesday, July 5, 2000 8:48 AM Remote Operations Remote Operations You can call the UX-84 from any tone dial telephone and play back your messages using the remote commands. You can also use these commands to change the reception mode and other settings. Remote code number To perform remote operations, you must first program a remote code number. This number is used to prevent unauthorised people from listening to your messages or changing the settings of your machine. The remote code number has been set to "001" at the factory. · Perform other operations: You can enter any of the commands described in the following section, Other remote operations. · Hang up: If you do not erase your messages first, they will be saved and any new messages will be recorded after them. If you want the UX-84 to resume normal operation immediately, press "*" twice before hanging up (in some cases, particularly when the Transfer function is used, the UX-84 may not accept new calls for one or two minutes after you hang up unless you first press "*" twice). Comments: 7 When a remote command is accepted by the machine, you will hear one beep. When entering a command, do not pause longer than 10 seconds between each digit. If you do, a 4-beep error signal will be issued and the digits entered up to that point will be disregarded. If an additional 10 seconds elapse without entry of a command, a further 4 beeps will be issued and the machine will disconnect the line. If you make two errors (causing two 4-beep signals to be issued) while entering your remote code number, the line will be disconnected. This prevents unauthorized people from attempting to guess your remote code number. 56 all-UX84H. book Page 57 Wednesday, July 5, 2000 8:48 AM Remote Operations Other remote operations 2. Answering Machine After listening to your messages, you can do any of the operations described below by pressing the appropriate keys on the telephone. Note: The following commands cannot be entered while messages are being played back. If you do not want to wait until playback ends to enter a command, first stop playback by pressing "0" and "#", and then enter the command. Changing the fax reception mode Select a new reception mode by pressing the keys as follows: · A. M. · TEL/FAX mode: "8", "4", and "#" Caution: In TEL and TEL/FAX mode, you will not be able to further change the reception mode. 8 1 (Example) Recording a new outgoing message 1 Press "4" and "*" on the telephone. 4 57 all-UX84H. book Page 58 Wednesday, July 5, 2000 8:48 AM Remote Operations 2 When you hear a short beep, speak into the telephone to record the new message. [. . . ] When Rapid Key E/POLL is set as a polling key, it cannot be used for Rapid Key dialling. 1 Press these keys: The display will show: POLLING FUNCTION 4 2 Press 1 to turn on the function, or 2 to turn it off. YES NO or 1 2 3 Press the STOP key to return to the date and time display. STOP 107 7. Special Functions all-UX84H. book Page 108 Wednesday, July 5, 2000 8:48 AM Polling (Requesting a Fax Transmission) Requesting transmission Note: A Rapid Key can only be used for polling if you lift the handset or press the SPEAKER key before pressing the Rapid Key. 1 Dial the fax machine you want to poll using one of the following methods: · Pick up the handset (or press the SPEAKER key) and press a Rapid Key or dial the full number. · Press the SPEED DIAL key and enter a 2-digit Speed Dial number. · Enter the full number using the numeric keys. (Example) ABC DEF 1 GHI 2 JKL 3 MNO 4 PQRS 5 TUV 6 WXYZ 7 8 9 2 Press Rapid Key E/POLL. [. . . ]