User manual HASBRO WORD CHAOS

[. . . ] 4 Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing batteries in the remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Watching TV Watching a TV programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operating the TV buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The power indicator changes to bright and a picture appears. POWER Power indicator 2 Select channel. With Behind the door CH / CH · Press CH and channels change as shown below. / 2 / 1 / 0 . . . With the number buttons (on remote control) CH CH 5 · To select a one-digit channel, such as 5, press . If "5-" is indicated, press to select one-digit input, and then 5 press again. · To select a two-digit channel, such as 15, press to select 1 5 the two-digit input. Press , and then press . TV/VIDEO 1 4 7 2 5 8 0 3 6 9 1 5 -115 PAL B/G CH CH CH MENU CH SURROUND NORMAL LANGUAGE 3 Adjust volume using . · The number of oval blocks " " indicates the volume level. The volume bar disappears approximately three seconds after the volume has been adjusted. / TV VOLUME 10 · When the power indicator lights up dimly, either CH / CH on the TV can be pressed to turn on the power. · The channel number is displayed in green for channels tuned by auto tuning and displayed in yellow for channels tuned using fine tuning. · When the power indicator lights up dimly, the TV is in Standby mode and power is still supplied to the TV. If you will not watch TV for a while, turn off the main power by pressing POWER on the TV set. Also, if you will not be at home for a considerable length of time, unplug the cord from the outlet. · The AV1 (or COMPONENT), AV2 input channels cannot be selected using CH / CH on the remote control. · FINE The frequency changes to allow fine tuning. 6 Press MENU until normal screen appears. · When you select AV1, AV2 for the channel position, the CH-SETTING menu changes as shown on the right and the colour mode changes in the following order: AUTO PAL SECAM N443 CH-SETTING POSITION COLOUR AV1 AUTO CH :SELECT :ADJUST MENU:RETURN N358 · Switching COLOUR system: Set the system to "AUTO" for normal TV reception. The AUTO mode automatically detects the receiving signal system and changes the reception system of the TV set. When the picture is not stable, switching to an appropriate system may improve the picture quality. · In a weak reception area, or under bad reception conditions, you can change the frequency by fine tuning. · When using FINE, the channel number changes from green to yellow. · To return the channel to its original frequency setting, follow the manual channel tuning procedure. See 15 . E 16 WORD CHAOS_12-16E 16 29/12/04, 9:01 am WORD CHAOS_12-16E Dimension: 176 x 250 mm ENGLISH FLE (M) Sdn. Bhd Settings and adjustments Picture adjustment TV/VIDEO 1 2 CH CH Press screen. MENU to call MENU MENU PICTURE SOUND FEATURE TIMER CH-SETTING 1 4 7 2 5 8 0 3 6 9 Press CH / select "PICTURE". CH to CH CH MENU 3 4 Press / display PICTURE menu. Press CH / CH select adjustment items. to PICTURE CONTRAST COLOUR BRIGHTNESS TINT HASBRONESS WHITE TEMP 50 0 +10 -10 SURROUND NORMAL LANGUAGE to MENU TV NORMAL 5 Adjust using / . · Wait for approximately three seconds to return to PICTURE menu. CONTRAST - 50 + 6 7 Repeat steps 4 and 5 above to adjust other items. Press MENU until normal screen appears. · Pressing NORMAL while a PICTURE selection is displayed, only the selected mode is reset to the standard (factory-setting) position. · Pressing NORMAL while a PICTURE menu screen is displayed will reset all the items of PICTURE menu to the standard (factory-setting) position. The following table lists the adjustment items shown in the PICTURE menu and how they change as you press / . Selected item CONTRAST COLOUR BRIGHTNESS TINT HASBRONESS WHITE TEMP Press To decrease contrast For less colour intensity For less brightness To move tint toward red For less sharpness To more reddish background Press - + + + - + To increase contrast For more colour intensity For more brightness To move tint toward green For more sharpness To more bluish background *: TINT can only be selected and adjusted when receiving NTSC broadcasts. E 17 WORD CHAOS_17-23E 17 29/12/04, 9:03 am WORD CHAOS_17-23E Dimension: 176 x 250 mm FLE (M) Sdn. [. . . ] · To cancel the timer setting, press NORMAL when " " is displayed on the left of " " so as to set the timer to "- - : - -". E 23 WORD CHAOS_17-23E 23 29/12/04, 9:04 am WORD CHAOS_17-23E Dimension: 176 x 250 mm FLE (M) Sdn. Bhd Connecting to a DVD player The DVD input terminals (COMPONENT-IN) on the rear of the TV can be used to input high-quality images from a DVD player. DVD input terminals Green : To Y Blue : To PB (CB) Red : To PR (CR) AV-1 IN OUT Red : To AUDIO IN (R) White : To AUDIO IN (L) R i AUDIO i L COMPONENT Y PB (CB) (MONO) PR (CR) VIDEO To colour-difference (component video) out terminals DVD player To audio out (L/R) terminals COMPONENT Y AV-1 IN OUT PB (CB) (MONO) R i AUDIO i L PR (CR) VIDEO Connecting the video terminals DVD input terminals Y COMPONENT-IN VIDEO PB(CB) PR(CR) DVD player Y or Y/Y PB(CB) or B-Y/Pb PR(CR) or R-Y/Pr Watching DVD Playback TV/VIDEO 1 TV/VIDEO COMPONENT 1 4 7 2 5 8 0 3 6 9 Press TV/VIDEO to select "COMPONENT", DVD input screen. CH CH MENU SURROUND NORMAL LANGUAGE 2 Turn on the DVD player and begin playback. TV · When connecting the TV to a DVD player via the Component-in terminals, the video and audio from the DVD player cannot be output through the Audio/Video out terminals on the TV. · Please refer to the operation manual of your DVD player for more information. · Be sure to fully insert the plugs of the connecting cables into the terminals on the TV set and video equipment. [. . . ]