User manual HASBRO WONDER WORLD TORPEDO RUN

[. . . ] If you are not sure how to do this, get help from a qualified electrician. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E, or by the safety earth symbol , or coloured green or green-and-yellow. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. This apparatus must be protected by a 13A fuse in the mains plug or distribution board. "WARNING: THIS APPARATUS MUST BE EARTHED" This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. [. . . ] The display will show: INITIALIZE FILM YES NO or 1 2 3 Press the STOP key to return to the date and time display. STOP 62 Chapter 5 Making Telephone Calls Your fax can be used like a regular telephone to make and receive voice calls. To make or receive a phone call, the power must be on. 1 Pick up the handset or press the SPEAKER key. Listen for the dial tone. SPEAKER or 2 Dial the number using one of the following methods: · Normal Dialling: Enter the full ABC DEF 1 GHI 2 JKL 3 MNO · Rapid Key Dialling: Press the appropriate Rapid Key. · Speed Dialling: Press the SPEED DIAL key, and enter the 2-digit Speed Dial number with the numeric keys. 3 Speak with the other party when they answer. · If you pressed the SPEAKER key, pick up the handset to talk. 63 5. Making Phone Calls telephone number with the numeric keys. 4 PQRS 5 TUV 6 WXYZ 7 8 9 Making Telephone Calls Comments: · While the handset of the fax is lifted (off hook), an extension phone connected directly to the fax cannot be used to speak with the other party. · The fax may interrupt a voice call received on an extension phone if the reception mode is set to A. M. If you are on a tone dial phone, you can prevent this by pressing any three keys on the phone immediately after you answer. (Note: Do not enter the code to activate fax reception: 5, *, *. ) Chain Dialling After lifting the handset, you can dial any combination of Normal Dialling, Rapid Key Dialling and Speed Dialling numbers. For example, if you have stored an area code or an access code for a special service in a Rapid Key, you can press the Rapid Key for that area code or access code, then dial the remainder of the number by pressing a Rapid Key, pressing number keys, or pressing the SPEED DIAL key and entering a two-digit Speed Dial number. Using the SEARCH/R key You can use the SEARCH/R key to search for a Rapid Key or Speed Dial number. First search for the number as described in Using the SEARCH/R key in Sending a Fax by Automatic Dialling in Chapter 2, then pick up the handset or press the SPEAKER key. The number will be dialled automatically (do not press the START/MEMORY key). Redial The last number called can be redialled by pressing the REDIAL key (it is not necessary to pick up the handset or press the SPEAKER key). When the other party answers, pick up the handset to talk. 64 Making Telephone Calls Issuing tone signals If you are on a pulse dial line, you can use the "*" key to temporarily issue tone signals when you press the numeric keys. This allows you to use certain telephone services which require entering tone signals. When you need to enter one or more tone signals, press the "*" key and then press the appropriate numeric keys. Connection Settings If necessary, you can use the following settings to improve the response of the answering machine connection to incoming calls. Quiet Detect Time This function causes the fax machine to take over the line and begin reception if a certain duration of silence is detected after the answering machine answers. This gives the best performance with most answering machines; however, you may need to adjust this setting depending on the disconnect time of your answering machine. Some answering machines may have unusually fast disconnect times (equal to or very slightly less than 4 seconds), which means that the answering machine may disconnect the line before fax reception can begin. In this case, try a Quiet Detect Time setting of about 3 seconds. If the fax machine is interrupting callers before they can leave a message, try a longer Quiet Detect Time setting. If your outgoing message includes a period of silence, make sure that the setting is longer than that period of silence, or re-record your outgoing message to shorten the silence. To change the Quiet Detect Time setting, reset Option Setting 11 as explained in Chapter 8, Option Settings. Note: Quiet Detect Time can be turned off by entering "00" for the time. Note, however, that the fax machine will not be able to receive faxes sent manually by Normal Dialling. 70 Activating the Answering Machine Hookup Select Auto Receive When this function is turned on, your fax will answer the call after 5 rings if the answering machine for some reason fails to answer before that time. This ensures that you will receive fax messages even if the answering machine's tape fills up or the answering machine is not turned on. If you want to turn it on, reset Option Setting 14 as explained in Chapter 8, Option Settings. Note: When this function is turned on, make sure that the answering machine is set to answer on 4 rings or less. If it isn't, the fax will always answer first, preventing callers from leaving voice messages. Quiet Detect Start Timing This setting can be used to delay the start of the Quiet Detect Time function. For example, if you want to insert a pause at the beginning of your answering machine's outgoing message to ensure clear detection of fax signals, you can use this setting to delay the start of silence detection so that the pause will not cause the fax to take over the line. [. . . ] A document has been loaded and the fax is waiting for transmission or copying instructions. This appears if you attempt to send a fax by automatic dialling and the line is busy or the receiving fax machine does not answer. (See Automatic Redialling in Sending a Fax by Automatic Dialling in Chapter 2. ) 11. Troubleshooting MEMORY PRINTING NO DATA NO # STORED OUT OF PAPER ON HOOK DIAL OVER HEAT PAPER JAMMED READY TO SEND RECALLING 117 Display Messages SEARCH DIAL The SEARCH/R key has been pressed. Press # or to search for an automatic dialling number, or press STOP to return to the data and time display. [. . . ]