User manual HASBRO WINNIE THE POOH

[. . . ] Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure. G G G Cautions on laser Wave length Pulse times Output power 785 nm ±10 nm (8. 141 µs ±0. 1 µs)/7 mm 0. 2 mW ±0. 02 mW Required in Appendix ZB of BS EN 60950 -- United Kingdom MAINS PLUG WIRING INSTRUCTIONS The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. Always refit the fuse cover after replacing the fuse on the moulded plug. [. . . ] Enables or disables image rotation (180°) of the front side in one-sided to two-sided copying or two-sided to one-sided copying. See page 71. 7 8 GENERAL INFORMATION 9 10 11 12 13 User programs 14 15 16 17 18 19 20 22 * These programs do not affect the copier functions unless certain optional equipment is installed. 36 USER PROGRAMS Setting the user programs 1 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and "­ ­" appears in the copy quantity display. 2 Enter a program number using the numeric keys. G G G The selected program number will blink in the copy quantity display. For example, to change the setting of the auto power shut-off timer, press key 3. Program name Auto clear time Preheat mode Auto power shut-off timer Stream feeding mode Auto power shut-off setting Border line for 2 in 1 or 4 in 1 Rotation copy Auto paper select mode Auto tray switching Auditing mode Account number entry Account number change Account number deletion Number of copies per account Resetting account Erase width adjustment Layout in 2 in 1 copy Layout in 4 in 1 copy Offset of paper output tray Image rotation in duplex copying Location of the margin Program No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 GENERAL INFORMATION For operation of these programs after step 3, see page 39. User programs 3 Press the START key. G For programs 1 to 9 and 16 to 22, the entered program number will be steadily lit on the left side of the copy quantity display and the currently selected parameter number for the program will blink on the right side. For programs 10 to 15 (programs for auditing accounts), the display varies with the program number. See page 39 for setting programs 10 to 15. G 37 USER PROGRAMS 4 Select the desired parameter using the numeric keys. G The entered parameter number will blink on the right side of the copy quantity display. For example, to change the setting of the auto power shut-off timer to 60 min. , press key 2. G Program name Auto clear time Parameters 0 OFF 1 30 sec. Stream feeding mode *0 OFF 1 ON Auto power shut-off setting 0 OFF *1 ON Border line for 2 in 1 or 4 in 1 * 0 OFF 1 ON Rotation copy 0 OFF *1 ON Auto paper select mode 0 OFF *1 ON Auto tray switching 0 OFF *1 ON Erase width adjustment 0 0 mm 1 5 mm Layout in 2 in 1 copy *1 Pattern 1 2 Pattern 2 Layout in 4 in 1 copy *1 Pattern 1 2 Pattern 2 Offset of paper output tray 0 Upper OFF, lower OFF Upper ON, lower OFF 2 Image rotation in duplex *0 OFF 1 ON copying Location of the margin *1 Left 2 Top *2 2 3 60 sec. 240 min. *2 3 *1 3 10 mm 3 15 mm 4 20 mm Pattern 3 4 Pattern 4 Upper ON, lower ON Upper OFF, lower ON GENERAL INFORMATION Factory default settings are indicated with an asterisk (*). If you select "0" (OFF) in a program, the corresponding function will be disabled. 5 Press the START key. G The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. User programs 6 To continue with other user programs, press the key and then repeat steps 2 to 5. 5. Press the START key. G The specified account will be deleted. To continue with other user programs, enter another program number. To exit the user program mode, press the light ( ) key. 40 USER PROGRAMS Program No. 14 is used to display the total number of copies made against each account number. 14 is entered, an account number will appear in the copy quantity display. G If no account number has been registered, "14E" will appear in the copy quantity display. The copier will return to step 2 on page 37. 1. Use the copy ratio display ( number. G ) key to select the account Use the key to advance through the account numbers. 2. Press and hold down the 0 key. G The number of copies made against the specified account number will be displayed. The two higher digits and the three lower digits will appear alternately while the 0 key is pressed. Example: 1, 234 copies G The upper limit for the number of copies is 49, 999. If the number of copies made reaches 50, 000, the number will be reset to 0 and counting will start again from 0. 3. 4. Repeat steps 1 and 2 for other account numbers. GENERAL INFORMATION To continue with other user programs, press the key and select another program number. To exit the user program mode, press the light ( ) key. User programs 41 USER PROGRAMS Program No. 15 is used to reset all accounts or to reset any desired individual account. [. . . ] Health Hazards: Acute oral toxicity ------------ LDL0 of this toner which is included in this developer is over 2, 000mg/kg. Mutagenicity ------------------ The toner, which is included in this developer, has been tested on Ames test. Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. [. . . ]