User manual HASBRO VOCTRON

[. . . ] G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from HASBRO ELECTRONICS (EUROPE) GmbH. SHOWVIEW is a registered trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under license from Gemstar Development Corporation. ALL OF THE FEATURES MENTIONED MAY NOT NECESSARILY APPLY TO YOUR VCR. (i) TINS-A083UMZZCoverGB 11/11/02 11:23 am Page 3 REMOTE CONTROL STANDBY 1. [. . . ] Press SET to confirm. Continue from step 2 above. GB-11 TINS-A083UMZZEnglish. book Page 12 Monday, November 11, 2002 9:39 AM BASIC OPERATION HOW TO USE THE SHOWVIEW® SYSTEM TO MAKE A RECORDING 7. If your VCR has long play facility and you wish to change the RECORDING SPEED, use the [H/J] to highlight SP. Press [K/L] to select standard play (SP), long play (LP) or Extended Play (EP) as required. DA T E 21 / 06 --/---/---/-TAPE 1/2 P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP * ------- 8. Using the [K/L] will select VPS/PDC ON or OFF ( = ON - = OFF). SET S P E E D :S P / L P : SE L ECT : CHANGE : ENT ER ME NU : E X I T 9. If you wish to enter further SHOWVIEW system recordings repeat this procedure. 10. When you have completed entering timer settings, press MENU to remove the menu from the TV screen. 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- 11. will be shown on SET V P S / P DC : ON - : OF F : SE L ECT : CHANGE : ENT ER ME NU : E X I T NOTES: · VPS/PDC is a signal broadcast by some TV stations which adjusts the start and stop time of your VCR recording. This ensures that if there is a change in broadcast time for your programme the VCR will still record the whole programme. It is essential that the start time as it appears in the TV listing is used to program the VCR, as this information is used to identify the VPS/PDC signal corresponding to your programme. If flashes a video tape has not been inserted into the VCR. · · · If the video tape is ejected when the VCR tries to record the record protection tab has been removed. If there are further recordings to be made, the VCR will return to TIMER STAND-BY. GB-12 TINS-A083UMZZEnglish. book Page 13 Monday, November 11, 2002 9:39 AM BASIC OPERATION HOW TO SET A DELAYED RECORDING You can make a maximum of eight delayed recordings up to a year in advance. · All the delayed recordings in the VCR's memory will be shown. · SET : SE L ECT : ENT ER ME NU : E X I T You can check the settings and change or cancel them. CHANGING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP * ------- 2. If you wish to change a delayed recording, press [K/L] to highlight the recording, then press SET. 3. Press [H/J] to highlight the setting to be changed and correct it by using the [K/L] or the NUMBER BUTTONS. 4. When all corrections are complete press SET, then press MENU. CANCELLING A RECORDING 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP * --/-- --:--:-- ----/-- --:--:-- ----/-- --:--:-- --- 1. If you wish to cancel a delayed recording, press [K/L] to highlight the recording to be cancelled, then press CLEAR. 3. NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER STAND-BY mode. GB-15 TINS-A083UMZZEnglish. book Page 16 Monday, November 11, 2002 9:39 AM ADVANCED OPERATION AUDIO AND YOUR VCR HI-FI STEREO SOUND Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The sound output from the VCR is controlled by the AUDIO OUT button on the remote control. If you wish to change the sound output you can use the AUDIO OUT button as follows: · · · · Press AUDIO OUT once. Pressing AUDIO OUT a fourth time, normal Hi-Fi stereo sound will be heard. [. . . ] FULL. , all the active features will also be shown on screen. 2. Programme number and channel Tape Status Audio output mode Tape speed Tape remaining Time Date Tape counter I SUPER P . SP 22 : 00 9 / 07 02 1 CH 5 9 ON S T E R EO LR R EM 1 : 0 5 0 : 00 . COUNTER, this display will show the tape counter and amount of tape remaining. 3. 4. DISPLAY OFF, this will remove the display from the screen. REM 1:05 0:00. 00 NOTES: · · · The default time and date will not be displayed if the clock has not been set. [. . . ]