User manual HASBRO STARWARS EPISODE I-COMMTECH READER

[. . . ] Connecting the water inlet hose • To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection. To a suitable hot water connection point: your dishwasher may be provided with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. Remove the appliance from all packaging and check that it has not been damaged during transportation. [. . . ] Press the ON/OFF button: the machine will emit a beep and the ON/OFF indicator light will illuminate. Open the door and measure out a suitable amount of detergent (see below). Select the wash cycle by pressing the SELECT WASH CYCLE button: the corresponding indicator light will illuminate. Start the cycle by pressing the START/RESET button: the machine will emit a confirmation beep. The WASH CYCLE PHASE indicator lights display the status of the cycle: Pre-wash, Wash, Rinse, or Drying. At the end of the cycle two short beeps will sound and the DRYING indicator light will flash. Switch off the appliance by pressing the ON/OFF button and close the water inlet valve. Open the door and wait for a few minutes before removing the crockery inside, in order to avoid burns. Loading the detergent A successful wash also depends on the correct amount of detergent being used, as recommended by the manufacturer. Exceeding the recommended amount does not result in a more effective wash and pollutes the environment. Only use detergent which has been specifically designed for dishwashers. For the first wash cycle only: fill the dispenser up to the edges with water. Position the funnel* provided correctly (see figure) and fill the salt dispenser up to the edges (approximately 2 kg); it is normal for a little water to leak out. Remove the funnel*, wipe away any salt residue from the thread and screw the cap on tightly, so that detergent does not leak into the dispenser during the wash cycle (this could damage the water softening system beyond repair). When necessary, measure out the salt before a wash cycle so that any saline solution which has leaked out of the salt dispenser is removed. Adjusting the amount of salt* It is possible to adjust the amount of salt used according to the hardness of the water in your area (this information is available from your local water board). Turn the arrow on the neck of the dispenser (see figure) towards the + or symbols, using the table below as a guide. Selector knob position / MED + Salt consumption (grams/cycle) 0 20 40 60 Hardness of the water Adjusting the amount of rinse aid If you are not completely satisfied with the washing or drying results, you may adjust the quantity of rinse aid used. Use a screwdriver to turn the dosage adjuster to one of the 6 pre-set positions (the default position is set to 4): • if there are white streaks on the crockery, set the adjuster to a lower number (1-3). • if drops of water remain on the crockery or there are limescale marks present after the cycle has finished, set the adjuster to a higher number (4-6). If you are using multi-functional tablets and you wish to further improve the drying performance of the appliance, fill the dispenser and set the dosage adjuster to 2. - If using multi-functional tablets fill the salt dispenser and set the adjuster to -; if the hardness of the water is greater than 60°fH, set it to +. [. . . ] Select a wash cycle that is suited to the type of crockery and to the soil level of the crockery using the Wash cycle table: - for dishes with a normal soil level, use the Eco wash cycle, which guarantees low energy and water consumption levels. - if the load is smaller than usual activate the Half load* option (see Start-up and use). If your electricity supply contract gives details of electricity saving time bands, run wash cycles during the periods when a lower tariff is applied. The Delayed start* button (see Start-up and use) helps you organise the wash cycles accordingly. [. . . ]