User manual HASBRO SESAME STREET READY FOR SCHOOL ELMO

[. . . ] Elevation button: Changes the height at which the paper stack is loaded onto and off of the Cart. Stack transport handle: Activates the paper stack transport system to move the paper stack from the Cart onto a work table or other finishing device. Locking casters: Lock: Stabilizes the Cart during transfer of the paper stack to and from the Cart. Vertical post Paper table support: Joins the paper table to the vertical post. [. . . ] Use special care when operating the Cart with paper stacks to avoid tipping, loss of load, or striking personnel or objects. Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 5 Safety Warnings • • • • • • • • • • • • • • • • • • • • • • Always look in the direction of travel. Keep a clear view and when the load obstructs visibility, travel with the load lowered. Watch swing clearance when turning near walls, racks, pillars, machinery, or other obstacles. Before you leave the Cart, fully lower the paper table and set the caster locks. Do not wear loose clothing such as ties and scarves, or dangling accessories such as bracelets, when operating the Cart to avoid entanglement. Never raise or lower the paper table unless the Cart is on a firm, level, even surface and the casters are in the locked position. Use extreme caution when raising or lowering the paper table when it is near other objects to avoid personal injury or damage to other objects. Never allow any object, including limbs, to go beneath the paper table to avoid personal injury or damage to other objects as the paper table nears the bottom of its range. Use caution when lowering the paper table to avoid personal injury or damage to objects that may have come between the paper table and base of the unit. Never operate the Cart when the edge of the paper stack is less than 1 inch (25 mm) from the front (loading edge) of the paper table. Never tilt the Cart when a paper stack is loaded. Pre-operation Inspection Workplace safety regulations require that the Production Media Cart (Cart) be inspected before each shift. Guide the Cart out until it clears the stacker. 16 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Operating the Xerox Production Media Cart (Nuvera) Transferring the Stack to the CP Bourg BSFEx Air Table This procedure assumes pick up from the XPS low position. Lower the Cart by pressing the lower part of the elevation button (approximate height 210 mm (8. 25 in. ). Move the Cart forward until the front of the horizontal post mates with the red docking station at the base of the Air Table. 4. Lock the casters. Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 17 Operating the Xerox Production Media Cart (Nuvera) 5. Gently lift up on the paper stack clamp near the clamp post, rotate it to one side, and rest it in the locator on the clamp post. 6. Turn the stock transport handle approximately 15 turns clockwise to transfer the paper stack to the Air Table. 18 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Operating the Xerox Production Media Cart (Nuvera) Offloading the Stack to a Work Table This procedure assumes pick up from the XPS high position (600 mm). Press the upper part of the elevation button to raise the media table height until it exceeds the height of the work table enough for the bottom of the paper stack to clear it. 2. Press down on the lock tab on the rear casters to stabilize the Cart. Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 19 Operating the Xerox Production Media Cart (Nuvera) 3. Gently lift up on the paper stack clamp near the clamp post, rotate it to one side, and rest it in the locator on the clamp post. 4. Turn the stock transport handle approximately 15 rotations clockwise to transfer the paper stack onto the work table. Note When transporting to a flat work table, the paper stack may shift and lose stack quality. Offloading the Stack to a Pallet This procedure assumes pick up from the XPS low position (210 mm) and the paper stack will be delivered to either a tined or smooth surface. Press the elevation button to set the media table height until it exceeds the height of the pallet enough for the bottom of the paper stack to clear it. [. . . ] Press the tab on the upper part of the caster lock on the rear casters to release them. 6. Guide the Cart out until it clears the stacker. 26 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Operating the Xerox Production Media Cart (Nuvera) 7. Close front door to continue stacker operation. Transferring the Stack to the CP Bourg BSFEx Air Table 1. Lower the Cart by pressing the lower part of the elevation button (approximate height 210 mm (8. 25 in. ). Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 27 Operating the Xerox Production Media Cart (Nuvera) 3. [. . . ]