User manual HASBRO RISK LORD OF THE RINGS TRILOGY EDITION

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following: • • • • Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit, different from that to which the receiver is connected. 5” Mounting Kit Brackets 6/32” pan head screws X 4 M3 flat head screws X 4 SATA power adapter SATA data cable cloning software CD SSDNow Tools Needed: ● Phillips head screw driver ● Computer system manual (optional) 4 SSDNow For Desktops System Requirements  Operating System: Windows Vista® (SP1), Windows XP® (SP3) and Windows 2000® (SP4)  Pentium processor or higher  128MB RAM  CD-ROM or DVD drive for bootable media creation  Available SATA Connector  Available 3. [. . . ] — If the SSD provided in this kit is smaller in capacity than the hard drive currently in your system, please confirm that the used capacity on the system hard drive is not larger than the capacity of your new SSD. Perform the following steps to determine the Used Space on the system hard drive: 1) Boot your computer to your desktop. 2) Double click on My Computer (Computer in Vista) located on your desktop or via the Start Menu. The Properties window for the C: drive will appear (Figure 1): Figure 1: (C :) drive Properties If the used capacity is greater than the capacity of the SSD, it is required that you move some of your data such as pictures, movies, music, etc. , external hard drive or USB drive) until the Used space is no more than 5 SSDNow For Desktops 85% of your new SSD capacity. The following chart may be useful as a guide: SSD capacity 32GB 40GB 64GB 80GB 128GB 160GB 256GB 512GB Adjusted HDD Used Space 27GB or less 34GB or less 54GB or less 66GB or less 109GB or less 136GB or less 218GB or less 423GB or less Adjusted HDD Used space = SSD capacity X 85% After the cloning process has been successfully completed, these files can be moved back to their original location on the hard drive. Handling Precautions To prevent damage from static electricity, observe the following precautions: ● Allow the drive to remain in the anti-static container until you are ready to install the SSD. — Wear a wrist strap and connect the ground strap to the computer case to minimize static electricity. Remove the system chassis cover according to the system manufacturer’s instructions. 5” mounting brackets (provided) to the SSD by aligning the mounting screw holes on the brackets with those on the SSD and inserting the M3 flat head screws provided. 5 inch drive bay inside your computer and install the SSD using the 6/32” pan head screws (provided). (Consult your computer system’s documentation for the correct key. ) 2) While in the system BIOS, look for an entry labeled "Drives or Hard Drives. " Select this field using the arrow keys on your keyboard and press Enter. Here, the spare SATA ports can be enabled or turned on by selecting the SATA port and changing the value to "On" or "Enabled". For best results, it is recommended that you enable or turn on all SATA ports during this process. 4) Restart the computer, booting to the software CD, and try the cloning process again. Note: The original partition sizes will be scaled according to the new drive size. If the new drive is smaller in size than the original drive, the partitions will shrink accordingly. If the new drive is larger than the original drive, the partitions will be enlarged proportionately. Once the cloning process is complete, a Disk Cloning was successful window will appear. 11 SSDNow For Desktops Set “Hard Drive Boot Priority” Your system is now configured with two bootable drives. [. . . ] In order to boot from your new SSD drive, you must enter the system BIOS to set "Hard Drive Boot Priority" so that your new SSD drive is set to boot first. While the system is restarting, activate the system setup program (BIOS) by repeatedly pressing a special key such as ESC, F1, F12 or DELETE. (Consult your computer system’s documentation for the correct key. While in the BIOS, change the "Hard Drive Boot Priority" so that the disk labeled "SSDxxxx" is in the first position. [. . . ]