User manual HASBRO PUZZ 3D TAJ MAHAL

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION The AC outlet shall be installed near the equipment and shall be easily accessible. FOR YOUR RECORDS Please record below the model number and serial number, for easy reference, in case of loss or theft. [. . . ] Then, from the differences, find irregular cycles (B) and regular cycles (C and D). These cycles will show you the following items necessary to program the tax table: T: Q: M1: M2: M: The tax amount collected on the minimum taxable amount (Q) The minimum taxable amount The maximum value of the minimum breakpoint on a regular cycle (C). € Range of the minimum breakpoint on a regular cycle: difference between Q and M1 or between M1 and M2 98 Procedure 2710 . Five digits @ @ M Ç @ t Repeat until the MAX point is entered. Four digits *1 First figure: The first figure to be entered depends upon whether the difference between a minimum breakpoint to be entered and the preceding minimum breakpoint is not less than $1. 00, enter “1, ” and when it is not more than 99¢, enter “0” or nothing. Second figure: The second figure depends upon whether your tax table is to be programmed as tax table 1, 2, 3 or 4. When your tax table is to be programmed as tax table 1, enter “1”; when it is to be programmed as tax table 2, enter “2”; when it is to be programmed as tax table 3, enter “3”; and when it is to be programmed as tax table 4, enter “4”. 4-3/8%), then the fractional portion (3/8) would be converted to its decimal equivalent (i. Note that the nominal rate (R) is generally indicated on the tax table. Note If you make an incorrect entry before entering the M in programming a tax table, cancel it with the Then program again from the beginning correctly. Department type You may program each department as one of the following three types. € Normal department • Hash department A hash department is used to enter the amount of a special “sale”, such as a gift certificate sale or for the receipt of payment for utility bills, theatre tickets, etc. Any amounts entered in this department are not added to the grand total except tax amounts. € Bottle Return (BR) • Gas department The gas department enables you calculate the quantity of gas sold in gallon by using a preset unit price when the sale amount of gas is entered. (quantity of gas = sales amount entered / preset unit price) Also gas discount can be automatically applied to the sales. (discount amount = total amount of gas x reduced unit price for each media; cash/check/charge) Note If your register has not been set for “Bottle return, Hash and gas dept. € by your dealer, you cannot program the department for those operations. Type of unit price entry You may select one of the following four types of unit price entry for each department. € Open and preset • Preset only • Open only • Inhibit department key 102 Procedure To program any dept. *1 Item: A B C Item validation printing Tare table number Scale entry Selection: Non-compulsory Compulsory Inhibit Enable Compulsory Normal SICS (Single Item Cash Sale) SIF (Single Item Finalization) Normal department Hash department Bottle return department Gas department Inhibit department key Open only Preset only Open and preset D Registration type E Department type F Type of unit price entry Entry: 0 1 0 thru 9 (0: not used) 0 1 2 0 1 2 0 1 2 3 0 1 2 3 Example Programming for department 3 Enter ABCDEF=000003 for department 3. @ 3 @ 000003 t Ç A thru F 103 Functional programming 2 PGM 2 2111 Direct Sign (plus/minus) • Assign a plus sign to departments for normal sales transactions. [. . . ] To detach the drawer, pull it forward fully with the till removed, and remove it by lifting it up. coin case Till Drawer 7 Opening the drawer by hand The drawer automatically opens normally. However, when power failure is encountered or the machine becomes out of order, slide the lever located on the machine bottom toward the rear. Lever 222 8 Before calling for service The malfunctions shown in the left-hand column below, labelled “Fault, ” do not necessarily indicate functional faults of the machine. [. . . ]