User manual HASBRO PIPEWORKS 1000-2000-3000

[. . . ] – The feet of the washing machine must be secured with holding brackets*. see above Also required, depending on the connection: – 1 hose clamp Ø 24-40 mm (exclusive dealers) to connect to a siphon page 4; water connection. Useful tools – Spirit level for installation. – Wrenches WAF 13: for loosening transport braces page 3 and page 5. Connect the water inlet hose (hoses) to the tap (taps) 3/4" = 26, 4 mm and to the solenoid valves. [. . . ] 2. 20 m) for standard model. Drainage into a siphon: Caution: the connection point must be secured with a hose clamp, Ø 24-40 mm (exclusive dealers). 1 2 3 4 Alignment Intense noise formation, vibrations and “wandering” may be the result of incorrect alignment. Transportation, e. g. when moving home After-sales service If you cannot rectify the fault yourself (Operating instructions; What to do if. . . We will always find a suitable solution and will avoid a visit from a service technician wherever possible. The contact details for all countries can be found in the enclosed after-sales service directory. Please give the after-sales service the product number (E-Nr. ) and the production number (FD) of the appliance. You will find this information on the inside of the washing machine door, on the opened service flap or at the rear of the appliance (depending on the model). 1. Drain residual water Operating instructions; Maintenance - drain pump. Release the water pressure in the inlet hose Operating instructions; Maintenance - filter in water inlet. Dismantle the hoses. Washing machine Aligning the washing machine with a spirit level 1. Loosen the lock nut using a wrench, by turning it in a clockwise direction. 2. Check the alignment of the washing machine with a spirit level and adjust if necessary. 2. – Lay hoses and cables in such a way that there is no risk of tripping. Scope of delivery depending on model Aqua Stop Aqua Secure & Standard Hot water Moisture inside the drum is due to final testing. Mains cable Water outlet Water inlet Installation surface – The machine must be stable so that it does not move around. Covers Elbow for fixing the drainage hose in place Adapter 1/2’’-3/4’’ (depending on model) Installation on a pedestal – The feet of the washing machine must be secured with holding brackets*. WMZ2200, WX9756, CZ110600, Z7080X0 Installation on a wood joist floor – If possible, place the washing machine in a corner. – The feet of the washing machine must be secured with holding brackets*. see above Also required, depending on the connection: – 1 hose clamp Ø 24-40 mm (exclusive dealers) to connect to a siphon page 4; water connection. Useful tools – Spirit level for installation. – Wrenches WAF 13: for loosening transport braces page 3 and WAF 17: for aligning appliance feet page 5. Installing the appliance – Install the appliance before connecting it to the power supply. – Do not remove the cover of the appliance! Hose and cable lengths depending on model Left-hand connection ~ 100 cm ~ 145 cm or Right-hand connection ~ 145 cm ~ 100 cm Installation in a kitchenette (underneath the worktop or fitted in a cabinet) – Recess width of 60 cm required. – Only install the washing machine underneath a continuous worktop that is securely connected to adjacent cabinets. ~ 90 cm ~ 135 cm Available from specialist dealers/the after-sales service: – Extension for Aqua-Stop or cold-water inlet hose (approx. 100 cm 2 Removing the transport braces – Before using the appliance for the first time, make sure that you completely remove transport braces and keep them for subsequent transportation. – If you need to transport the appliance at a later date, always re-affix the transport braces to prevent damage to the machine. – Store the screw and sleeve together. Water connection depending on model Water inlet Caution: do not bend, squash, modify or cut through (otherwise its strength is no longer guaranteed). [. . . ] We will always find a suitable solution and will avoid a visit from a service technician wherever possible. The contact details for all countries can be found in the enclosed after-sales service directory. Please give the after-sales service the product number (E-Nr. ) and the production number (FD) of the appliance. You will find this information on the inside of the washing machine door, on the opened service flap or at the rear of the appliance (depending on the model). Washing machine Product number Production number Rely on the professionalism of the manufacturer. [. . . ]