User manual HASBRO NERF N STRIKE VULCAN EBF 25

[. . . ] – If the water pressure is higher, install a pressure reducing valve. hose clip may also be required for connecting the siphon (available from specialist retailers). -> Page 4: Water connection Useful tools – Spirit level for aligning the appliance. Spanner for adjusting the appliance feet. D Installation area – – – – It is important to ensure that the machine is stable to prevent it from "wandering"! [. . . ] *The holding brackets can be obtained from a specialist store or from after-sales service. cm 2. Insert the covers, which you will find in the bag containing the documentation. Drainage into a sink/bath tub: Note: Secure the drainage hose to prevent it from slipping out of the sink. When the water is being pumped out of the washing machine, check that the water drains away quickly enough. Do not insert the end of the drainage hose in the water that has been pumped out. There is a risk that water will be drawn back into the washing machine. Drainage into a siphon: Note: Secure the connection with a 24-40 mm dia. hose clip (available from a specialist retailer). Built-under/built-in appliances Build these appliances under/in before connection to the power supply. For WS, WLX, WLG series Connection on left side Connection on right side ~ 90cm Installed in between kitchen units (built-under or built-in) max. 100cm ~ 145cm cm ~ 105 ~ 150 cm For safety reasons in built-under installation, a metal cover* must be assembled by a specialist in place of the appliance cover plate. *The metal cover can be obtained from a specialist store or from after-sales service. ~ 100-130cm ~ 150-180cm 1 Available from dealer/after-sales service: – Extended water inlet hose, approx. – Install the washing machine only under a continuous worktop that is connected firmly to the adjacent cupboards. 2 3 4 Alignment Incorrect alignment may cause loud noises, intense vibrations and ”wandering”. Alignment will be carried out by customer service or authorised technicians. Covers for holes left by removing the transport bolts. Depending on the connection – A 24-40 mm dia. hose clip may also be required for connecting the siphon (available from specialist retailers). -> Page 4: Water connection Useful tools – Spirit level for aligning the appliance. Spanner for adjusting the appliance feet. Installation area – – – – It is important to ensure that the machine is stable to prevent it from "wandering"!Keep the surrounding area dry and well-vented. Hose and cable lengths For WM, WAX, WAE series Connection on left side ~ 100cm If installing the appliance on a stand – It is essential to secure the washing machine feet using holding brackets*. Connection on right side ~ 150cm ~ 110cm If installing the appliance on a wooden joist floor max. 100cm ~ 140cm c ~ 110 m ~ 15 0 cm *The holding brackets can be obtained from a specialist store or from after-sales service. Built-under/built-in appliances Build these appliances under/in before connection to the power supply. For WS, WLX, WLG series Connection on left side Connection on right side ~ 90cm Installed in between kitchen units (built-under or built-in) max. 100cm ~ 145cm ~ 105 cm ~ 150 cm For safety reasons in built-under installation, a metal cover* must be assembled by a specialist in place of the appliance cover plate. *The metal cover can be obtained from a specialist store or from after-sales service. ~ 100-130cm ~ 150-180cm 1 Available from dealer/after-sales service: – Extended water inlet hose, approx. – Install the washing machine only under a continuous worktop that is connected firmly to the adjacent cupboards. max. 100cm – If possible, install the washing machine in a corner. It is essential to secure the washing machine feet using holding brackets*. 2 Removing the transport bolts – Before using the appliance for the first time, always remove and retain all 4 transport bolts from the back of appliance. – Be careful when handling these to avoid injury. Water connection – To prevent leaks or water damage, follow the instructions in this chapter. – Do not remove the water inlet hose frequently as the loose connection will lead to leaks. [. . . ] Optimum water pressure in the mains: 100-1000 kPa (1-10 bar) – When the tap is turned on, the water flow should be at least 8 l/min. – If the water pressure is higher, install a pressure reducing valve. Use a spirit level to check the alignment of the washing machine and correct it if necessary. A damaged power cord must be replaced by an electrician only. If a residual current-operated circuit-breaker is used, use only a type which guarantees compliance with the regulations that are currently valid. [. . . ]