User manual HASBRO MONOPOLY POKEMON

[. . . ] 500 entries Caller picture PC interface, e. g. , for managing directory entries, ringtones and screensavers u . . . . . . . . . . . . . . . . . . . www. gigaset. com/gigasetS800H Gigaset C59H handset u u u u u u Illuminated graphic colour display (65k colours) Polyphonic ringtones Directory for approx. 150 entries SMS (prerequisite: CLIP must be enabled) Room monitor . . . . . . . . . . . . . . . . . . . www. gigaset. com/gigasetc59h Gigaset SL78H handset u u u u u Illuminated graphic colour display (256k colours) Polyphonic ringtones Directory for approx. [. . . ] If the messages memory is full and Activation: On has been selected, saving is interrupted and you will receive an instruction to delete old messages. When you switch the answering machine on, the remaining memory time is announced. If the time has not yet been set, an appropriate announcement is made (set time page 17). The phone is supplied with pre-recorded announcements for Answer & record mode and for Announce only mode. If a personal announcement has not been recorded, the relevant pre-recorded announcement is used. Mode: v Announcements Rec. End Press the display key to end the recording. Recording personal announcements/ advisory messages 50 Operating the Gigaset S800A base answering machine Cancel recording with a or Back. You can rerecord the announcement with New. Please note: u Recording ends automatically if the max- imum recording time of 170 seconds is exceeded or there is a break in speech for more than 2 seconds. u If you cancel the recording, the prerecorded announcement is used again. u If the answering machine's memory is full, it will switch to Answer only mode. Delete old messages and the answering machine will automatically switch back to Answer & record mode. Once you have deleted your announcement, the relevant pre-recorded announcement is used again. Deleting personal announcements/ advisory messages Please note Deleting announcements can take some time. Playing back messages The date and time of each message is logged (provided this has been set, page 17) and displayed during the playback. If the memory is full, you will hear an end tone, the recording is aborted, and the call recorded up to that point is listed in the answering machine list as a new message. v Call Screening Handset / Base (= on) Change Select display key to activate/ deactivate the function. Call screening can be simultaneously activated on the base and handset. Permanently activating/deactivating call screening Deactivating call screening for the current recording You can deactivate the function for your own handset during the recording. Silence Press the display key. parameters Setting the recording The answering machine has already been preset at the factory. v Recordings You can enter data in the following fields: Length: Select maximum recording time 1 min. , 2 min. , 3 min. Ring Delay: Select when the answering machine should accept a call: Immediately, after 10 sec. , 18 sec. , 30 sec. Save Press the display key. 53 Operating the Gigaset S800A base answering machine Information about ring delay In Automatic mode, the following applies for ring delay: u If there are no new messages, the answering machine answers a call after 18 seconds. u If there are new messages, the answering machine answers a call after 10 seconds. 15 seconds that there are no new messages (otherwise the answering machine would have already accepted your call). There are no call charges if you hang up now. Operating when on the move (remote operation) You can check and activate your answering machine from any other telephone (hotel, pay phone etc. ), or initiate ringback from the answering machine with an SMS. Prerequisites: u You have set a system PIN other than 0000 ( page 74). u The phone you are using for remote oper- Please note: You can configure your telephone so that the first ring is suppressed on all calls ( page 44). This means that the time selected for the ring delay predetermines how long the caller must wait before the answering machine accepts the call. ation has tone dialling (DTMF), i. e. , you hear different tones when you press the keys. Alternatively, you can use a code transmitter (available from your mobile phone retailer). Calling the answering machine and playing back messages ~ 9~ Dial your own number. [. . . ] u Press display key to delete the character to the left of the cursor. u The first letter of the name of directory entries is automatically capitalised, followed by lower case letters. General specifications DECT standard GAP standard No. of channels Is supported Is supported 60 duplex channels Radio frequency range 18801900 MHz Duplex method Channel grid Bit rate Modulation Language code Transmission power Range Base power supply Environmental conditions in operation Dialling mode Time multiplex, 10 ms frame length 1728 kHz 1152 kbit/s GFSK 32 kbit/s 10 mW, average power per channel Up to 300 m outdoors, up to 50 m indoors 230 V ~/50 Hz +5C to +45C, 20% to 75% relative humidity DTMF (tone dialling)/ PD (pulse dialling) Setting upper/lower case or digits Repeatedly press the hash key # to change the text input mode. 123 Abc abc Writing digits Upper case * Lower case Pin connections on the telephone jack 3 2 1 4 5 6 1 2 3 4 5 6 unused unused a b unused unused * First letter in capitals, all others in lower case The active mode is indicated at the bottom right of the screen. 83 Additional functions via the PC interface Writing an SMS/names pressing the corresponding key. [. . . ]