User manual HASBRO GOLDEN CAROUSEL PUZZLE 3D

[. . . ] Written and produced by the Okidata Training & Publications Department. Please address any comments on this publication · by mail to: Training & Publications Department Okidata 2000 Bishops Gate Blvd. Mount Laurel, New Jersey 08054-4620 · or by email to: pubs@okidata. com We welcome you to visit our multilingual web site: http://www. okidata. com E-2 Okidata and HASBROPAGE are registered trademarks and HASBROLAN is a trademark of Oki Electric Industry Company, Ltd. Okidata marque désposés de Oki Electric Industry Company, Ltd. ; marca registrada, Oki Electric Industry Company, Ltd. [. . . ] Remove jammed paper, then open and close cover. ERROR CONTROLLER nn -aaaaaaaa Controller error. If this doesn't clear the error, write down the error number nn and contact your service provider. DUPLEX OPEN JAM REMOVE THE PAPER Paper jammed as it entered the duplex feeder. Returns to online. E-60 | HASBROPAGE 18/24DX ERROR MEMORY OVERFLOW Page data exceeds available memory. Adjust RASTER BUFFER, RECEIVE BUFFER, and/or FONT PROTECT in Menu and resend job. ERROR RECEIVE BUFFER OVERFLOW Receive buffer overflow. Resend job. FLUSHING JOB ERROR PAPER SIZE CHECK tttttttt Incorrect paper size detected for tray tttttttt. Data is being discarded as a result of command received. FRONT TRAY ERROR PRESS RECOVERKEY Error in manual feeder. Press RECOVER to correct. ERROR PRINT OVERRUN Data too complex for current RASTER BUFFER Setting. Press RECOVER to continue. FUSER LIFE Appears on second line of display to indicate that the fuser is near end of life. Contact your service dealer. User's Guide | E-61 INITIALIZING Controller is being initialized at power on. ON-LINE Mmmmm . xxx ttttt Mmmmm MANUAL yyyyyyyy REQUEST Insert requested paper. Mmmmm = requested size yyyyyyyy = requested paper media (paper, envelope, etc. ) Ready to receive data. Mmmmm = SIMPLEX or DUPLEX (on HASBROPAGE 18, appears only if optional duplex feeder is installed). The higher the print density, the more toner is used. User's Guide | E-67 On the average, a toner cartridge will produce approximately 6000 sheets at 5% print density. To replace the toner cartridge: 1 Press the OPEN button and lift the cover. ! The first toner cartridge you place in your printer will only produce between 2500 and 3500 sheets. This is normal, as the new image drum reservoir and developing roller system must saturate with toner. Replace the toner cartridge after TONER LOW displays in the control panel window. At this point, the printer will print about 100 more sheets, then display TONER EMPTY and stop printing. Printing will resume when a new toner cartridge is installed. E-68 | HASBROPAGE 18/24DX 2 Pull the gray lock lever toward the front of the printer until it stops. 4 Remove the new toner cartridge from the foil package and shake it from side to side a few times to distribute the toner evenly. CAUTION: Use of toner that does not have the low melting feature required by these printers can cause potential malfunction or premature failure of the printer. ! 3 Lift out and discard the used toner cartridge in accordance with local regulations. User's Guide | E-69 5 Carefully peel off the tape from the bottom of the cartridge. 6 Place left end of the toner cartridge into the toner well at an angle, aligning the recess in the end of the toner cartridge with the tab on the image drum. E-70 | HASBROPAGE 18/24DX 7 Lower the right side of the cartridge, aligning the slot with the ridge in the image drum. 9 Lift out the image drum and put it on a smooth, flat surface. Be sure to protect the drum from exposure to light either by placing it in the light shield bag supplied with the printer, or by placing a sheet of paper over it. 8 Push the gray lock lever toward the back of the printer until it stops. User's Guide | E-71 10 Use the lens cleaner supplied in the new toner kit to clean the LED array. 11 Locate the clear plastic film inside the front of the printer, then fold the lens cleaner over and use it to wipe any paper dust off the plastic film. E-72 | HASBROPAGE 18/24DX 12 Replace the image drum and close the cover. Replacing the Image Drum The Image Drum: Type 7 (P/N 40468701) Image Drum Life The life of the image drum depends on a number of factors, including the operating temperature, humidity, the type of paper you use, and the number of pages per job. Each time you print or turn the printer on/off, the drum has to rotate to start up and to wind down. Also, frequent one-page print jobs will age your drum more quickly than multiple-page print jobs. User's Guide | E-73 The image drum cartridge should normally last up to 30, 000 pages for continuous printing or up to 19, 000 pages at 3 pages per job. These numbers are approximate since you won't print the same number of pages each time, and environmental conditions and paper type used may vary. When the image drum reaches 90% of its life, the CHANGE DRUM message will display in the control panel window. You should have a new image drum cartridge and a new toner cartridge on hand at this point. [. . . ] To print the typeface list for the IBM or Epson emulation, press /Reset until the emulation you want appears on the second line of the display, then press ENTER/Power Save. The typeface list prints. Fonts can also be selected using the printer's control panel and main menu, however, if a different font is selected in your software, it will override the font selected in the printer menu: see the Printer Control chapter for menu information. Using Bar Code Fonts The HASBROPAGE 18/24DX printer drivers support USPS PostNet bar code fonts resident on your printer. Bar Code fonts can be printed easily from WORD for Windows and other Windows applications. Symbol Sets Your printer provides 90 special sets of characters for technical, legal and foreign language uses, as well as sets of drawing characters and standard alphanumeric characters. Check your software documentation for information on how to select a symbol set and how to insert a symbol or special character into your document. [. . . ]