User manual HANSOL 920D

[. . . ] 4 OSD Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power Management Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Standard Signal Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power management circuit signaled by the computer system, will reduce power consumption when the computer system is not in use. Monitors with nonglare/antistatic screens are compliant with MPR 1990 Emissions standards and meets requirements for CE Marking. TCO : (option) 3 Color Monitor Controls - OSD controls The OSD apears on the screen when you press MENU button. "ON SCREEN MENU" controls include the following extended controls such as Size, Position, Geometry Distortion, Color Temp. , Degauss, Moire on & off, Language, OSD-Position, Recall, Cont. EXIT from OSD : Press this ( ) button in the main menu and submenu. Additional front controls Power Switch : Turn the monitor power on or off, When the power is on, the LED is lit. 4 Color Monitor Controls - OSD Menu OSD MENU 1. · ·+ · Proceeds to NO. 3 Proceeds to NO. 4 No meaning CONTROL 4. · + Increases or decrease the Contrast position and size Menu control guide 5. / + : Refer to / + MENU :Toggle Horizontal and Vertical directly. · After choosing , push MENU button. · MENU : Push this button again & again to change the H/V-position. · MEUN : Push this button again & again to change the H/V-size. The Geometry controls allow you to adjust the curvature or angle of displayed image. · Pincushion : Increase or decrease the curvature of the sides either inward or outward. · Parallelogram : Increase or decrease the tilt of the sides either to the left or right. · Trapezoid : Increase or decreases the bottom of the screen to be the same as the top. · Pin Balance : Increase or decrease the curvature of the sides. · Top Corner : Increase or decreases the curvature of the top sides. · Bottom Corner : Increase or decrease the curvature of the bottom sides. · Rotation : Rotate the entire display to clockwise or counterclockwise. 7. · MENU : Push this button again & again to change the H/V-OSD position. " USER, 6500k, 9300k " Color adjustment is available only in USER mode. · / + : Move the bar with or + key to select the user · MENU : Press MENU button to access the sub-menu. [. . . ] Press a key on the keyboard or move the mouse, in case the screen power-saver mode has blanked the screen. Check the pin assignments and signal timings of the monitor and your video card with respect to recommended timings and pin assignments. Caution A minimum interval of 20 minutes should exist before the Degauss Button is used a second time. Do not hold the button down continuously. Image is scrolling or unstable Picture is fuzzy Picture bounces or a waving pattern is present in the picture Move electrical devices that may be causing electrical interference away from the monitor. [. . . ]