User manual HANNA INSTRUMENTS HI 955201

[. . . ] Untitled-10 1 2 Instruction Manual HI 955201 - HI 955202 HI 955301 - HI 955302 Portable Microprocessor Printing and Logging PT-100 Thermometers Dear Customer, Thank you for choosing a Hanna Instruments Product. Please read this instruction manual carefully before using the instrument. This manual will provide you with all the necessary information for the correct use of the instrument, as well as a precise idea of its versatility in a wide range of applications. These instruments are in compliance with directives EN 50081-1 and EN 50082-1. [. . . ] If this happens, data will continue to be stored into memory, and it is always possible to print them at different time (see above). It is possible to insert a new paper roll during logging session (see page 31) Once in the logging mode, the interval cannot be changed. Exit the logging mode first (pressing the ALT and the LOG keys) before setting the new interval. If the PRINT key is pressed while in logging mode, a printout is produced without affecting the PRINT running sample number. ALT UP DOWN TEMP TIME LOG TO STOP LOGGING Press ALT and LOG keys simultaneously, this will generate a log exit status printout. ALT UP DOWN TEMP TIME LOG Log number Total sample number ==07== 0016 10-01-96 0005M *16. 25 LOG EXIT Date/Time PRINT PAPER LOG CH ALT UP Notes: · It is recommended to use the adapter during logging with printing mode, especially when many printouts are going to be taken. 21 22 Untitled-10 23 24 TO SCAN STORED DATA ON DISPLAY Press the LOG key. The display will show the log number and the page number of the next logging. Press UP and the temperature will be displayed. °C CH LOG While pressing the ALT key, press DOWN until the log number to scan appears on the secondary display. The primary display will show the number of samples of that particular log. Continue pressing UP to display all the memorized data of the same log one by one in the above sequence i. e. Press the DOWN key to revert back to sampling time and move back through samples. To exit from the recall mode press LOG. ALT DOWN LOG Note: this mode will not alter data into memory Press ALT and TEMP simultaneously. This now shows the date on which the log started. ALT DATE TEMP Press UP and the time will be displayed. TIME UP TO PRINT STORED DATA Once a log number is selected by using the ALT and DOWN, as detailed in the chapter "TO SCAN STORED DATA ON DISPLAY" you can print all or part of that log section by using the ALT and PRINT keys. The printer will start to print the logged section beginning with the selected sample number without altering the content of the memory. Note: It is always possible to print only the sample shown on the display by pressing PRINT. ALT DOWN PRINT ALT PRINT 23 24 Untitled-10 25 26 Note: Before proceeding with printing, make sure there is enough paper for the data to be printed. When the paper is finished the meter will not advise the operator and printouts could be lost. If this happens, stop the printer by pressing ALT PAPER and PAPER simulta- PRINT neously. Insert a new paper roll and repeat the instruction above starting from the last printed sample number (see chapter "PRINTER MAINTENANCE" on page 31 for changing paper roll). WORKING SAMPLE (HI 955301 and HI 955302 only) The following is a step by step procedure of a typical monitoring situation where we have assumed that you have already inserted the batteries and set the date and time correctly. It is an example of a meter used to monitor and store every 2 minutes. The meter will log 10 samples but print only 3, display the data contained in sample number 1 and print samples 5 through 10. Example: Step One - Setting the printing/logging interval at 2 minutes: Press ALT and TIME keys twice. The time will appear on the primary display with a number representing the printing/logging interval blinking. ALT UP TEMP TIME Press either the UP or DOWN keys until a blinking "2" appears. TIME INTV UP DOWN Press ALT and TIME keys to exit. The display will now show the current time together with the selected interval of 2 minutes. ALT UP INTV TIME TEMP TIME Step Two - Entering the log mode: Press ALT and LOG keys. Initially, "L 01" will appear on the primary display. ALT UP DOWN LOG TEMP TIME LOG 25 26 Untitled-10 27 28 The meter is now in the printing/logging mode utilizing log number 1, page 16. "LOG" and P 15 shown in the secondary display indicate that the meter has entered the log mode, and has 15 pages of available memory remaining. After the initial printout, the time and printing/ logging interval will reappear. TIME Step Four - Leaving the log mode: Once the number of samples stored in memory has reached 10, press the ALT and LOG keys. [. . . ] the paper caught under the cover and prevented printer from advancing paper feed). Replace the battery cover and secure screws. - 1. 5V 1. 5V 1. 5V 1. 5V + + + - + - SCREW POTS RESET Insert the paper edge in the printer slot and feed the printer by pressing the PAPER key. PAPER 33 34 Untitled-10 35 36 BATTERY REPLACEMENT If "LO BAT" appears on the display, it is an indication that the batteries are running down. If it appears during printing, it means that 200 printouts can be made before the batteries are exhausted. When there is only sufficient power for 100 printouts, the "LO BAT" sign is displayed continuously on the LCD. °C CH Note: The instrument uses the following configuration. + - LOBAT Battery replacement must only take place in a non hazardous area using the battery types specified in this instruction manual (see page 35). It is recommendable to purchase Hanna Instruments HI 710005 and HI 710006 voltage adapters that use the proper polarity configuration. [. . . ]