User manual HAMA ROC2407 CODES

[. . . ] it is recommended to perform a simple RF transmission test before mounting. 1) Place the monitor in your selected indoor location and install adapter & batteries (see "Battery & adapter installation for the monitor" section above) 2) Place the anemometer horizontally in your selected outdoor location. Loosen the screws on the battery door with a small Phillips screwdriver and open the battery door. 4) If valid wind direction, wind speed and channel-1 temperature/humidity readings are shown on the monitor within 10 minutes, the RF transmission is successful and the anemometer & monitor are within the effective transmission. [. . . ] Use the compass on the anemometer and turn the wind vane so it is pointing due north. Unscrew the 4 screws from the battery compartment cover (identifiable by the battery diagram markings). Remove the cover and insert 2 AA alkaline batteries as indicated by the polarity symbols marked inside the battery compartment. The rain cup has been sealed to prevent tipping and damage during shipping. Before first use please remove the seal to allow the rain cup to fill and empty when rainfall occurs. Total rainfall reading (in this case "0" mm or inch) will appear within 2 minutes if the RF transmission is successful and the monitor & rain gauge are now within the effective transmission range. If total rainfall "- - - - " stop flashing and stay on the display after 2 minutes of searching, the RF transmission is failed. Reset the rain gauge by removing all batteries from the rain gauge and wait for 10 seconds before re-installing the batteries again. Mounting the rain gauge Before mounting the rain gauge, be sure the rain gauge & monitor are within the transmission effective range and batteries are installed. Hold the base of the rain gauge flat against the mounting surface then use a level to make sure the rain gauge (as it rest on the mounting surface) is horizontally level. Use a pencil to trace the inside of the mounting holes on the base of the rain gauge to mark the screw locations. Press "Heat Index/Dew Point" button once to show the respective indoor or outdoor heat index on the display. IN/OUT dew point Dew point is the saturation point of the air, or the temperature to which the air has to be cooled in order to get condensation. Press HEAT INDEX / DEW POINT button twice to show the respective indoor or outdoor dew point reading on the display. Press "RAIN/CLEAR" repeatedly to switch between the different modes and the corresponding "DAILY", "WEEKLY", "MONTHLY" or "TOTAL" icon will appear In daily, weekly or monthly rainfall display, hold "RAIN/ CLEAR" to clear all daily, weekly & monthly rainfall reading to zero. in total rainfall display , hold "RAIN/ CLEAR" to clear total rainfall reading. Press "RAIN UNIT" on the back casing to change the unit between mm and inch. Rainfall history This unit has a large capacity memory that can store and display: · Daily rainfall (up to last six days as well as current day) · Weekly rainfall (up to last six weeks as well as current week) · Monthly rainfall (up to last six months as well as current month) Press "RAIN" to select daily, weekly or monthly rainfall display mode. Press "RAIN HISTORY" repeatedly to scroll through the current & last 6 days/weeks/months data corresponding to your selected rainfall mode. The precise rainfall reading of the selected period will be shown on the display. Example 1: In April, press "RAIN HISTORY" repeatedly in the monthly rainfall mode until "­3" bar chart is shown. The bar chart and reading indicate the monthly rainfall record in January (from 1st Jan to 31st Jan) Example 2: On Wednesday, press "RAIN HISTORY" repeatedly in the weekly rainfall mode until "-1" bar chart is shown. [. . . ] Rain Gauge reading 66 inch Transmission (Anemometer): up to 100M (228 feet) in open area, RF434 MHz Transmission (Rain Gauge): up to 50M (164 feet) in open area, RF434 MHz Clock: DCF77 Radio-Controlled, Quartz back-up Power · AA x 2 pieces for rain gauge Registration and Safety Certification/General Information This device bears the CE symbol as specified by the provisions of Directive R & TTE (1999/5/EC). KG hereby declares that this device is in compliance with the basic requirements and other relevant guideline and regulations of the 1999/5/EC guideline. Antenna icon without signal strength indicates the past reception is not successful (Daily synchronization is still enabled). To enforce searching of radio-controlled time signal immediately, press repeatedly until the antenna icon flashes. [. . . ]