User manual HALCRO LOGIC SSP100

[. . . ] Owner's Manual SSP100 Surround Sound Processor SSP80 Surround Sound Processor www. halcro. com 1 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Safety Information. . . . . . . . . . . . . . . . . . . 5 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Protection from overheating . . . . . . . . . . . . . . . . . . . . . . . 7 Additional important safety instructions for the US . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interference warning -- US FCC regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Viewing the Menus on the OSD . . . . . . . . . . . . 41 SSP Setup and Operation . . . . . . . . . . . . . . . . . . . . . 45 SSP80 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 SSP100 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This level corresponds to sound levels in public cinemas. To access the `Speaker setup' menu: o Enter the Main Menu. o Press ENT to select. 50 Level setup Output channel levels are adjusted in Level setup. LEVEL SETUP > Left Center Right Right surround Right back Left back Left surround Subwoofer EXIT To set up output channel levels: o From the `Speaker Setup' menu, use the UP or DOWN keys to highlight `Level Setup' and press ENT. o Use the UP or DOWN keys to highlight the speaker/channel level you want to adjust. o Use the LEFT or RIGHT keys to adjust the level to your desired setting. o Use the UP or DOWN keys to highlight EXIT and press ENT to return to the `Speaker setup' menu 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB DISTANCE SETUP > Left Center Right Right surround Right back Left back Left surround Subwoofer EXIT 6ft 5ft 6ft 3ft 0ft 0ft 3ft 0ft You can engage the noise calibration signal by pressing the TEST key on the UTSR1. The test signal stays on the channel until no level change is made during the last few seconds. Pressing the TEST key again disengages the noise signal. Distance setup Speaker distances must be correctly setup to ensure sound arrives simultaneously to the listening position. Note: The adjustment range is from ­6. 0 dB to +6. 0 dB with 0. 5 dB steps per issue (15). 51 To set up speaker distances: o From the `Speaker Setup' menu, use the UP or DOWN keys to highlight `Distance Setup' and press ENT. o Use the UP or DOWN keys to highlight the speaker/channel distance you want to adjust. o Use the LEFT or RIGHT keys to adjust the distance to the correct setting. o Use the UP or DOWN keys to highlight EXIT and press ENT to return to the `Speaker setup' menu. Size setup The `Size setup' subwoofer settings. SIZE SETUP > Main speakers Center speaker Back speakers Subwoofer Subwoofer filter Subwoofer freq. Enhanced bass EXIT · set speakers that are able to handle full frequency signals to `Large' and those that cannot, to `Small' if a speaker is not present (such as Center), set it to `No' set THX speakers to small 80 Hz Large Small 2Small Yes On 80 Hz-THX Off defines speaker and Surround speakers Small Note: The adjustment range is from 0ft (0m) to 63ft (21m). Note: The maximum difference in distance from speakers to the listening position is 15 ft (5 m). Refer to `Display setup', `Distance units' to change setup from feet to meters. Distance values that are `Too distant' are highlighted in a different color (usually red). The highlighted speaker should be moved closer or the nearest speaker should be move further away. · · 52 To set up speaker sizes: o From the `Speaker Setup' menu, use the UP or DOWN keys to highlight `Size setup' and press ENT. o Use the UP or DOWN keys to highlight the speaker/channel size you want to adjust. o Use the LEFT or RIGHT keys to adjust the size to your desired setting. o Use the UP or DOWN keys to highlight EXIT and press ENT to return to the `Speaker setup' menu. o If setup is complete for all settings, use the UP or DOWN keys to highlight EXIT and press ENT to exit the Speaker setup, followed by the Main Menu. Aux channel setup `Aux channel setup' allows user configuration of channel 9 and 10 outputs, also known as `Aux channels'. AUX CHANNEL SETUP > Ch 9 config setup -Level -Delay Ch 10 config setup -Level -Delay EXIT 0 dB 0 ms 0 dB 0 ms Note: The subwoofer crossover range is from 40 Hz to 140 Hz with 10 Hz steps. The crossover frequency defines the frequency below, which the low frequency signal does not travel to small speakers, but is redirected to large speakers and/or a subwoofer. [. . . ] Changes in the appearance of the product resulting from normal wear and tear, moisture, or atmospheric conditions are not warranted. The warranty shall be void and of no effect if any of the following occur: · · · · · · the defect has resulted from improper, unreasonable, or negligent use the defect is a result of accident, tampering, alteration, or modification the defect is a result of improper installation or setup by a third party the unit's serial number has been removed, altered, or made illegible Halcro is not liable for incidental or consequential damage of any kind Halcro does not warrant system design or installation 88 Transferability Transferability means that the warranty stays with the product from the date of original purchase through the full warranty period, regardless of who owns the product. The Halcro warranty is transferable, providing that the original sales receipt or proof of purchase is supplied to both subsequent owners and to Halcro when ownership changes. If service is required We suggest that you work with your authorized Halcro dealer when the need for technical service, training, or applications advice arises. If your Halcro product requires service or repair, it should be shipped to Halcro or your authorized Halcro dealer to be returned to the factory for service. [. . . ]