User manual HAIER XQG50-QF800

[. . . ] IILevel A11 21 A12 a WASH D1 12 DOOR LIGHT 3 b 6 B7 B8 b IPREFILL C7 a FILL C1 C1 b SPIN C2 N 8 E11 EV Pre EV F TM E12 F 11 12 1 5 D7 6 D5 a LOW SPIN 10 13 22 23 B3 4 b SPIN D2 D2 D1 E2 E1 D3 10 /13 b a SPIN WASH E3 10 /13 a SPIN 11 P1 B4 P2 b WASH C4 7 C3 5 TP T M 10. Keep away from heat sources and direct sunlight to prevent plastic and rubber components from aging. 11. During installation, ensure that the electric cable is not trapped by the washing machine and avoid damage to the electric cable. I2 4 PCB 7 D I3 H WASH b 14 / 11 D9 D10 DISTR C11 a DISTR b 8 E9 C9 D11 D12 SPIN C12 IMP. Make sure that the washing machine is securely connected to the water supply, take the necessory precautions or contact the local service center if the connection is poor or there is a water leakage. [. . . ] (Attention: the packing bolts and rubber hose should be kept in a safe place for later use) Drainage failure Drainage hose is blocked Drainage hose end is below 100cm above the floor level Strong vibration during spin Some packing fixing bolts removed Washing machine on a uneven surface Operation stops before completion of the wash cycle Water or electricity failure Fig 2 Adjusting the position of the washing machine . There are adjustable feet under the bottom of the washing machine. Before use, the washing machine should be adjusted, as shown in figure 3, so that it is level. Excessive foam in the drum The detergent is not a Iow foam type Excessive detergent has been used Fig 3 4 13 Maintenance 1. If the washing machine is left idle for a long period, drain any remaining water in the machine and replace the drainage hose. For the detergent compartment similar to figure (a), raise the compartment slightly to remove and replace after cleaning. Use a soft cloth dampened with soapy liquid to clean the machine case and rubber components. Do not use corrosive or abrasive chemicals or solvents. Installation Connection of water inlet hose and washing machine 1. Place the water inlet hose nut on the connector of the water inlet valve. water inlet hose nut 2. slightly shake the water inlet hose nut to see if it is tightly and properly fixed. connector of water inlet valve 4. Cleaning the Filter (once a month) Press the lower edge of the filter compartment cover to open; (Fig1-2) Remove the filter by turning counterclockwise; (Fig3) Flash clean with running water; Filter replacement is the reverse of removal, Caution: Attention shall be paid to ensure that the filter is replaced correctly to avoid possible leakage. Water drainage hose The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine. Use the water drainage support supplied as an accessory for proper installation of the water drainage hose . fix the water drainage hose support with waterproof sring. Do not use an excessively long water drainage hose and contract the authorized technician if the water drainage hose needs to be extended. the water drainage hose should not be extended more than250cm. (longer extension will result in concurrent water inflow and outflow). The diameter of the extension hose should be the same as the original hose. caution:water drainage hose must not be immersed in water. the original and extension hoses should be tightly connected . fig. 1 fig. 2 fig. 3 Fig (a) Connection of power supply 5. To prevent blockages to the water supply or the ingress of contaminants, clean the water inlet and inlet water filter regularly. If the washing machine is left idle for a long period turn off the water and electricity supply and open the door slightly to prevent the formation of moisture and odors. If the machine is to be moved a distance location, replace the vibration mounting locks which were removed during installation as shown below. The socket conforms to the maximun power Ioad(The maximum current Ioad of the socket and power supply cable should not be less than 15A). The power supply socket and the plug of the washing machine compatible, if they are compatible , Refer to a washing machine technician or a Haier designated service point for power cable replacement. Supplementary earth cable should not be necessary if the socket is connected to the earth. Supplementary earth cable should be installed on the upper back of the washing machine andconnected to an earth if the power supply socket has no earth connection. Remove the back cover. Replace the rubber plugs. Insert the bolts. Tighten the bolts with the Replace the back spanner provided. [. . . ] Detergent selection Only special Iow foam detergent should be used in automatic drum washing machine, form blended or wool fabrics special detergent should be used. dry cleaning solvent should not be used such as trichhloroethylene or alike (caution :load the required amount of detergent only). 3. Laundry treament sort out clothes according to type and extent of dirt. There are three types of clothes: cotton, synthetical and woolen (silk) fabrics. [. . . ]