User manual HAIER L37V6-A8K

[. . . ] TFT-LCD COLOUR TELEVISION RECEIVER OWNER'S MANUAL This User's Manual is applicable for the following models: L26V6-A8, L26V6-A8K, L32V6-A8, L32V6-A8K, L37V6-A8, L37V6-A8K, L42V6-A8, L42V6-A8K, L32A9A, L32A9A-A, L32A1A, L32A1A-A Please READ this manual carefully before operating the unit, and keep it for future reference. *Please read this manual carefully before using your television and keep this manual in a good place for future reference. *To achieve the best performance of your television, read this User's Manual carefully and properly store it for future reference. *Information of screen displays and figures in the User's Manual may vary due to technical innovations. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Warning *To avoid electric hazards, it is strongly suggested that the back cover not be opened, as there is no any accessory inside the casing. *A lighting flash mark in a triangle: A potentially hazardous situation, which, if not avoided, could result in serious injury by high voltage. [. . . ] Select Balance to balance right and left sound channels of the television. When indication value of Balance increases toward 50, sound of the right and left speaker becomes stronger and weaker, respectively. When indication value of Balance decreases toward -50, sound of the right and left speaker becomes weaker and stronger, respectively. The AAA Windows in advanced menu tracks picture contrast and color to improve the quality of picture in terms of brightness and sharpness. The advanced menu is displayed on the screen in various scales for user to select. English-18 System setup It is possible to select language, OSD transparency, position and screen display of the menu as follows: 1. Press Menu button once, and the CH+/- button until the following menu appears on the screen: TV/AV1//AV2/S-Video: CH+ Language Suspend Mode Background English OFF OFF Top Left Opague OFF Auto VOL- MENU VOL+ A B C OSD Position OSD Transparency OSD Stretch Color System CH- Set Enter YUV YPbPr YCbCr)/USB/D-SUB/DVI Language Suspend Mode Background OSD Position A B C English OFF OFF Top Left Opague OFF OSD Transparency OSD Stretch Set Enter English-19 System setup 2. Press VOL+ button on the remote controller to enter the menu of system setup. Press VOL+/- to adjust values level. OSD language option Repeat step 3 and 4 to select the language either Chinese or English. Suspend mode Repeat step 3 and 4 to set on or off Suspend Mode. 5 minutes after the Suspend Mode is set, the system will enter an energy efficiency status (standby mode). VOL- CH+ MENU VOL+ Background ON/OFF Repeat step 3 and 4 to select Background ON/OFF when no signal appears on the screen. CH- OSD Position Repeat step 3 and 4 to locate OSD freely on the screen for the most desirable position, including top left , top center , top right , center left , center, center right , bottom left , bottom center and bottom right. Note: OSD Position can only be selected when OSD Stretch is not intended. OSD Transparency Repeat step 3 and 4 to select semi transparency and opaque background of OSD. OSD Stretch Repeat step 3 and 4 for option of OSD Stretch on or off. Color system option In TV/AV1/AV2/Svideo mode, repeat step 3 and 4 to set the color system of the front interface among the options of automatic, PAL, PAL60, NTSC3. 58, NTSC4. 43 and SECAM. Automatic mode is usually set as default. English-20 Other functions Position and phase adjust In YUV and D-SUB input mode, H-Position, Phase and Scope of pictures can be adjusted to eliminate transverse line interference and decentered picture as follows: When YUV/D-SUB input mode is set. Press Menu button on the remote controller and CH+/- for option of picture position adjust. The menu display is as follows: CH+ VOL- MENU VOL+ H-Position V-Position Phase A B C 50 50 50 CH- Picture Position Enter H-Position V-Position Phase Frequency A B C 50 50 50 50 Auto Adjust Picture Position Enter CH+ VOL- MENU VOL+ CH- 2. Press VOL+ button on television and remote controller to enter the menu of picture position setup. Press VOL+/- for desired adjust parameter option until satisfactory value is achieved. When VGA signals are received, the automatic mode is used for parameter adjustment. (excluding HDTV 1080P, 1080i and 720P series) English-21 Other functions Timer setup If Off-time, On-time and Remind Time are intended in TV/AV1/AV2/S-Video/YUV/USB(USB only for the mo dels that have the function) , follow the instructions as below: 1. Press Menu button of television and remote controller, and the CH+/- button for timer setup menu. The menu display is as follows: CH+ VOL- MENU VOL+ Clock OFF Time ON Time ON Prog. A B C -- --- --- ----- --- -- CH- Remind Time Remind Prog. Timer Enter 2. Before activating timer setup, the clock must be correctly calibrated or otherwise the timer cannot be adjusted. If current time setting is cancelled, all previously set performance of the timer will also be inactivated. Note: The timer setup will not affect setup of the Sleep button and vice versa. [. . . ] If this kind of USB mobile devices are used in the stream media play system, the problem of identification failure might occur. The same problem may also happen with computers, not fault of televisions. 8. It is suggested that the external devices with USB2. 0 interface be used to improve velocity of information reading and continuity of information play. English-26 Connection of external AV devices Some external signal sources, including VCR, VCD, DVD and PC, can be connected to the television. Antenna input 1. Link radio frequency output of VCR to the radio frequency input on rear side of the LCD television. [. . . ]