User manual HAIER KD12W

[. . . ] - After removing the packing, check to make sure that the appliance is not damaged. - The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. - Fundamental rules to follow when using the appliance: * Never touch the dishwasher with wet hands; * We discourage the use of extension cords and multiple sockets; * During installation, the power supply cord must not be excessively or dangerously bent or flattened; Close-up View (Control Panel) A B C D Upper Rack Rack Height Adjustor Top Spray Arm Lower Rack E F G H Bottom Spraye Arm Washing Filter Detergent and Rinse Aid Dispenser Salt Container Cap E Technical Characteristics KD12W ON OFF Width Depth Height 60 cm 60 cm 85 cm 12 standard place settings 0. 03-0. 6 MPa 220-240V~ 50Hz 2100W AB C D Capacity Mains water pressure Power voltage A B C ON-OFF Button ON-OFF Light Handle For Opening Door D E Knob For Selecting Cycle Program Symbols Total absorber power . 1. GB GB . 2. Salt Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. [. . . ] To prevent the formation of rust, load the salt just before beginning a wash cycle. 1 0 14 M NT M NIT L M L Salt Selector c o n s u m p t i o n Autonomy (cycles/2kg) position (Grams/cycle) Level Clarke degrees ºdH mmol/l 2 NQ PS NU QQ NIU QIQ =?J? OM SM 3 4 PS TN QR UV QIR UIV jba ?H? QM SM QM OR [TN [UV [UIV . 3. GB GB . 4. Loading the Dishwasher Turning on the Appliance Starting a wash cycle Before placing the dishes in the dishwasher, remove larger food particles to prevent the filter from becoming clogged, which results in reduced performance. If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they are soaked before washed. - Make sure that the plug for the appliance is inserted into the wall Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. - Load the dishwasher (see the section entitled, "Loading the Dishwasher" on page 5). - Pour in the detergent (see the section entitled, "Salt, Detergent and Rinse Aid" on page 3 and 4). - Turn the knob located on the right of the control panel in clockwise direction until the number or symbol for the cycle setting is aligned with the reference mark (see the section entitled, "Wash Cycle Table" on page 8). STOP How to use the lower rack We recommend that you place the most difficult to clean items on the bottom rack: pots, pans, lids, serving dishes and bowls, as shown in the figure to the right. It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm. 1 Load for 12 Standard Settings - Press the ON-OFF button, and the ON-OFF light will turn on. At A cycle that is underway can only be modified if it has been this point, the wash cycle will begin. Otherwise, the detergent may have alIf you forget to load some of the dishes ready been used, and the appliance may have already drained The wash cycle can be interrupted by pressing the ON-OFF button. If this is the case, the detergent dispenser must You can then load additional dishes and turn the appliance back be refilled (see the paragraph entitled, "Loading the Detergent" 2 on. The cycle will start where it left off. Cancelling or modifying a wash cycle setting How to use the upper rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, plates, small bowls and shallow pans (as long as they are not too dirty). - Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height by using the knobs located on both sides of the rack itself (see fig. B). Adjust the upper basket to the higher level and you have more space to accommodate those taller pans and trays in the bottom basket. 3 At the end of the wash cycle When the knob stops turning and is aligned with a STOP mark 4 (see figure), the cycle has finished. Turn off the appliance using the ON-OFF button, turn off the water supply and open the door of the dishwasher. on page 4). Rotate the knob in clockwise direction to the desired cycle setting (see the section entitled: Starting a wash cycle ?F. Then, turn the dishwasher back on using the ON-OFF button. fig. A fig. B . 5. GB GB . 6. Energy Saving Tips Wash Cycle Table Cycle Selection Information Description of Cycle Pre-wash with cold water. Very dirty dishes, pots and pans (not to be used with Rinse with cold water. K 30g - It is important to try and run the dishwasher when it is fully loaded to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. [. . . ] After turning off the water tap, unscrew the end of the water supply hose, remove the filter and clean it carefully under running water. Then, return the filter to its place and tighten the water supply hose back into position. fig. 2 Troubleshooting The Dishes Are Not Clean It may occur that the dishwasher does not function properly or at all. Before calling for assistance, Iet us see what can be done first: Have you forgotten to press one of the buttons or to perform an essential operation?Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60°C. [. . . ]