User manual HAIER HSU12XHA

[. . . ] Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get damaged prior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal. Safety Instructions and Warnings Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very important observations relating to the assembly , operation and maintenance of the air conditioner. The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following instruction. [. . . ] For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select Auto operation 3. Unit stop Press ON/OFF button, the unit stops. About Auto Operation Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation according to room temperature. 9 Operation Cool Operation Remote controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select COOL operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under dispalyed wind speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 10 Operation Dry Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. Regarding the ambient temperature display during the heating operation. Every time the button is pressed, time settingdecreases l min, if kept depressed, it will decrease rapidly. It can be adjusted within 24 hours. 4. Timer confirming for TIMER ON After setting correct time, press TIMER button to confirm " " on the remote controller stops flashing. 5. Time setting for TIMER OFF Just press HOUR button , follow the same procedure in "Time setting for TIMER ON" 6. Time confirming for TIMER OFF After time setting, press SET button to confirm. To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved. 17 Operation POWER/SOFT Operation POWER Operation Remote Controller When you need rapid heating or cooling, you can use this function. Selecting of POWER operation Press POWER/SOFT button. Every time the button is pressed, display changes as follows: BLANK SOFT POWER Stop the display at " ". In POWER operation status: In HEAT or COOL mode, fan speed automatically runs in HI mode for 15 min then returns to original status setting. To cancel POWER operation Press POWER/SOFT button twice, POWER/SOFT disappears. SOFT Operation You can use this function when silence is needed for rest or reading. Every time the button is pressed, display changes as follows: BLANK POWER SOFT Stop the display at " ". In SOFT operation mode, fan speed automatically takes "LO". To cancel SOFT operation Press POWER/SOFT button once, POWER/SOFT disappears. Hint During POWER operation, in rapid HEAT or COOL mode, the room will show inhomogeneous temperature distribution. Long period SOFT operation will cause effect of not too cool or not too warm. 18 Operation Health airflow Operation 1. Press ON/OFF to starting The liquid crystal will display the working state of last time (Except timer, sleeping, power/soft and health airflow). [. . . ] 6. Do not place objects infrared rays couldnít penetrate within the human sensorís perception range. Note: If intelligent operation doesnít meet your desire, e. g. slight human activity couldnít be sensed, it shall be cancelled. About installing position of air conditioner (indoor unit) and sensible zone of human sensor: The dashed area shown in the figure is the sensible zone and the blank area is the dead zone. (Taking a 12 m2 room as example) Horizontal direction as shown follows: about 2. 2m air conditioner 100 o bed air conditioner bed Sensible zone Sensible zone desk chair sofa desk sofa about 2. 2m about 3. 6m about 1. 4m 65 o 100 o chair about 3. 6m air conditioner air conditioner bed 100 o Sensible zone Sensible zone desk chair sofa about 0. 7m about 3. 6m about 3. 6m The horizontal zone where human activity could be detected by the human sensor is about 100o. [. . . ]