User manual HAIER HSU-18HEA03

[. . . ] Always remember to unplug the air conditioner before openning inlet grill. Inadequate repairs may result in a major source of danger for the user of the air conditioner. Disposal of the packaging of your new air conditioner All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment. The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping bag made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon. All these valuable materials may be taken to a waste collecting center and used again after Do not damage any parts of the air adequate recycling. [. . . ] r When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. 2 R-03 batteries, resetting key (cylinder) Remove the battery cover: HEA LTH ON/ OFF FAN DE MO SW TIM ING ER CLO CK SET K LOC EP SLE RES ET Slightly press " Load the battery: " and push down the cover. Be sure that the loading is in line with the" + "/"-" pole request as illustrated. Put on the cover again Confirmation indicator: In disorderation, reload the batteries or load the new batteries after 6 mins. Note: Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key. Power failure resume(please set and apply as necessary) If sudden power failure occurs, the unit will resume original operation when power is supplied again. Note: When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is resupplied, or press ON/OFF to turn off the unit when power resumes. 7 Operation Auto, Cool Dry, Heat and Fan operation (1) Unit start Press ON/OFF button, unit starts. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: Operation mode AUTO COOL Remote controller Display board SWING HEALTH ON/OFF DRY HEAT FAN FAN MODE Unit will run in selected mode. TIMER CLOCK (3) Select temp. setting on LCD. SET SLEEP LOCK RESET (4) FAN Press FAN button. For each press, fan speed changes as follows: AUTO LO MED HI Unit will run at selected fan speed. COOL or DRY mode , otherwise, condensate water might occur. Hints As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow oblique downwards will be much more helpful for a better air circulation. 9 Operation HEALTH Operation 1. Unit start Press the ON/OFF switch HEALTH ON/OFF 2. Health anion function FAN Press HEALTH button remote controller and display board . is displayed on the is displayed on the TIMER MODE SWING CLOCK SET SLEEP 3. To Cancel HEALTH Model Press the " HEALTH"again, then the healthy function stops. . LOCK RESET When indoor fan motor is running, it has healthy process function. (It's available under any mode) NOTE: If the unit which you purchased has healthy function, follow it. If not, please ignore. Brief introduction to health anion function The anion generator in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room. 10 Operation TIMER Operation Set Clock correctly before starting Timer operation You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF (1)After unit start, select your desired operation mode. Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. HEALTH ON/OFF (2)TIMER mode selection PressTIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON AM FAN MODE OFF PM ON AM N 12:00 OFF ON PM OFF 12:00 blank SWING 12:00 12:00 TIMER CLOCK TIMER ON TIMER OFF TIMER ON-OFF TIMER ON-OFF Select your desired TIMER mode (TIMER ON or TIMER OFF), ON or OFF will flash. SET SLEEP LOCK RESET (3)Timer setting Press HOUR / button. It can be adjusted within 24 hours. (4)Confirming your setting After setting correct time, press SET button to confirm, "ON" or "OFF" stops flashing. Timer mode indicator on indoor unit lights up. To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Hints After replacing batteries or a power failure happens, Time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if timer setting is the same as previous one. 11 Operation TIMER ON-OFF TIMER ON-OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON AM OFF PM ON OFF ON PM OFF 12:00 blank HEALTH ON/OFF 12:00 12:00 N 12:00 AM TIMER ON TIMER OFF TIMER ON-OFF TIMER ON-OFF FAN Select TIMER ON-OFF. "ON" will flash. MODE SWING (3)Time setting for TIMER ON Press HOUR button. If button is kept depressed, time will change quickly. Time will be shown on LCD. [. . . ] Cause or check points When unit is stopped, it won't restart immediately until 3 minutes have elapsed to protect the system. When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner. During unit operation or at stop, a swishing or gurgling noise may be heard. (This noise is generated by refrigerant flowing in the system. ) During unit operation, a cracking noise may be heard. [. . . ]