User manual HAIER HSU-18,22H03R2DB

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-18H03/R2(DB) HSU-22H03/R2(DB) Please read this operation manual before using the air conditioner. No. Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled . Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO COOL operation starts when room temp. is higher than temp. setting. Temp. setting+2oC Temp. setting Ultra-low air flow Air conditioner is running under displayed wind speed In DRY mode, when room temperature becomes 2OC higher than temp. setting, unit will run intermittently at LOW speed regardless of FAN setting. 5. Unit stop On reaching temp. setting +2 C unit will run in mild DRY mode. o Press ON/OFF button, the unit stops. 11 Operation Fan Operation 1. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP operation is not available. 12 Operation Heat Operation 1. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT 6 Then Select HEAT operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly. Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly. Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed wind speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 13 Operation (5)Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. COOL About 10o HEAT About 60o Up and down (Use remote controller) Press SWING button, vertical flap will move within the range shown in the Fig. Press SWING button stop it at a fixed position. Left and right air flow adjustment (manual) Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o HEAT About 60o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6)Unit stop Press ON/OFF button. Vertical flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit. Hints As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow downward will be much more helpful for a better air circulation. It is harmful to your health in summer to go frequently in and out of places where temp. [. . . ] Every time the button is pressed, display changes as follows: BLANK POWER SOFT Stop the display at In SOFT operation mode, fan speed automatically takes"LOW" To cancel POWER operation Press POWER/SOFT button twice , POWER/SOFT disappears. Hints: During POWER operation, in rapid HEAT or COOL mode, the roor will show inhomogeneous temperature distribution. Long period SOFT operation will cause effect of not too cool or not too warm. 18 Operation Emergency and Test Operation Emergency operation: Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, the" Pi "sound is heard once, which means the start of this operation. [. . . ]