User manual HAIER HSU-12RE03/R2

[. . . ] (Don't adjust it manually. ) Remote signal receiver A beeping sound is generated when a signal from remote controller is received. Power indicator Lights up when unit starts. Timer mode indicator Lights up when Timer operation is selected. Operation mode indicator Lights up during compressor running. Actual inlet grille may vary from the one shown in the manual according to the product purchased Outdoor Unit HSU-07RE03/R2 HSU-09RE03/R2 HSU-12RE03/R2 HSU-18RE03/R2 HSU-22RE03/R2 OUTLET INLET CONNECTING PIPING AND ELECTRICAL WIRING DRAIN HOSE 3 Parts and Functions Operation Buttons and display of the remote controller. 1. FAN 1 2 3 4 11 12 13 14 15 MODE SET ON A U T O 5 OFF o C AM PM 6 7 8 9 10 18 19 20 AUTO LO MED HI ON/OFF TEMP Used for unit start and stop. Used to select AUTO run, COOL, DRY, HEAT and FAN operation FAN TIMER SWING CLOCK 14. HOUR 21 Used to select fan speed LO, MED, HI, AUTO Used to set clock and timer setting. [. . . ] To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed. (TIMER ON/OFF needs reelecting) Cautions: Note: On cooling only unit, heating mode is not available, The above information is the After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. No with those displayed in actual Timer mode: No, Fan speed :AUTO operation. Hints 7 Operation COOL, HEAT and DRY operation Recommendations: (1) Unit start Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. Press ON/OFF button, unit starts. (Not Timer setting) Power indicator on indoor unit lights up. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN ON/OFF o C AM TEMP Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 6 1 MODE 3 3 SET (3) Select temp. setting on LCD. 2 FAN TIMER 4 SWING CLOCK 5 SLEEP HEALTH (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LOCK RESET AUTO LO MED HI COOL operation starts when room temp. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. Temp. setting, unit will run in mild DRY mode. Hints On cooling only unit, heating mode is not available. When starting it next time, just press ON/OFF button and unit will run in previous status. 8 Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. COOL About 10 o HEAT About 60o Up and down (Use remote controller) Left and right air flow adjustment Press SWING button, vertical flap will move within (manual) the range shown in the Fig. Press SWING button stop it at a fixed position. Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o HEAT About 60o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. Vertical flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit. Hints As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow downward will be much more helpful for a better air circulation. It is harmful to your health in summer to go frequently in and out of places where temp. More than this, unit's load can be reduced and power consumption cut down as well. AM refers to morning and PM to afternoon ON/OFF TEMP MODE 1 3 5 SET FAN TIMER 6 SWING 2 CLOCK 4 (4) Time confirming for TIMER ON After time setting, press TIMER button to confirm. Time displayed: Unit starts at x hour x min. SLEEP HEALTH LOCK RESET (5)Time setting for TIMER OFF Follow the same procedures in "Time setting for TIMER ON". (6) Time confirming for TIMER OFF After time setting, press SET button to confirm, "OFF" stops flashing Time displayed: Unit stops at X hour X min. To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. 11 Operation HEALTH Mode operation (1) Press the ON/OFF switch. " (2) Press the "HEALTH" once, " is displayed, now the air conditioner is operating the health function. [. . . ] Cleaning of the air filter. Once every two weeks Proper temperature Closing of doors and windows during operation Curtains or blinds for windows Effective use of the timer. Avoid time-wasteful operation Never fail to observe the followings Do not sprinkle water over the unit. Do not block the inlet or outlet. Do not pull power plug. Do not use for other purposes. Such as food preservation plant cultivation or animal breeding. 16 Trouble shooting Before asking for service, check the following first. Phenomenon The system does not restart immediately. Cause or check points When unit is stopped, it won't restart immediately until 3 minutes have elapsed to protect the system. When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner. [. . . ]