User manual HAIER HSU-12LEA03

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-05LEA03 HSU-07LEA03 HSU-09LEA03 HSU-09LEA03G HSU-09LEA03U HSU-12LEA03 HSU-12HEA03 HSU-12LEA03G HSU-12LEA03U HSU-18LEA03 HSU-18HEA03 HSU-18LEA03G HSU-18LEA03U HSU-22LEA03 HSU-22HEA03 HSU-22LEA03G HSU-22LEA03U HSU-24LEA03 Please read this operation manual before using the air conditioner. 0010517097 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled . Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed. (TIMER ON/OFF SLEEP SWING needs reelecting) Cautions: Note: On cooling only unit, heating mode is not available, The above information is the After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. :No with those displayed in actual operation. 9 Operation Cool Operation (1) Unit start Press ON/OFF button, unit starts. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN ON/OFF TEMP Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 5 2 FAN 1 3 3 SET MODE (3) Select temp. setting on LCD. TIMER 4 SWING CLOCK SLEEP HEALTH (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: AUTO LO MED HI LOCK RESET Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. (5) Unit stop Press ON/OFF button, the unit stops. Hints On cooling only unit, heating mode is not available. When starting it next time, just press ON/OFF button and unit will run in previous status. No reelecting is needed. (TIMER ON/OFF SLEEP SWING needs reelecting) 10 Operation Dry Operation (1) Unit start Press ON/OFF button, unit starts. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN ON/OFF TEMP 5 2 FAN 1 3 3 SET MODE Unit will run in operation mode displayed on LCD. setting on LCD. 4 SWING CLOCK SLEEP HEALTH (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LOCK RESET AUTO LO MED HI COOL operation starts when room temp. setting. Ultra-low air flow Unit runs at the speed displayed on LCD. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. Temp. setting, unit will run in mild DRY mode. (5)Unit stop Press ON/OFF button, the unit stops. Hints On cooling only unit, heating mode is not available. When starting it next time, just press ON/OFF button and unit will run in previous status. No reelecting is needed. (TIMER ON/OFF SLEEP SWING needs reelecting) 11 Operation Heat Operation (1) Unit start Press ON/OFF button, unit starts. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN ON/OFF TEMP Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 5 2 FAN 1 3 3 SET MODE (3) Select temp. setting on LCD. TIMER 4 SWING CLOCK SLEEP HEALTH (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: AUTO LO MED HI LOCK RESET IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. (5) Unit stop Press ON/OFF button, the unit stops. Hints Remote controller can memorize each operation status. [. . . ] AM refers to morning and PM to afternoon ON/OFF TEMP MODE 1 SET 3 FAN 6 TIMER 5 SWING 2 4 CLOCK SLEEP HEALTH (4) Time confirming for TIMER ON After time setting, press TIMER button to confirm. Time displayed: Unit starts at x hour x min. LOCK RESET (5)Time setting for TIMER OFF Follow the same procedures in "Time setting for TIMER ON". (6) Time confirming for TIMER OFF After time setting, press SET button to confirm, "OFF" stops flashing Time displayed: Unit stops at X hour X min. To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. 8 Operation Emergency operation and test operation Emergency Operation: Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, the " Pi "sound is heard once, which means the start of this operation. In this operation, the system automatically selects the operation modes, cooling or heating, according to the room temperature: Room Designated temperature temperature Above 23 C Below 23 C o o Pi Timer mode No No Fan speed AUTO AUTO Operation mode COOL HEAT 26 C 23 C o o It is impossible to change the settings of temp. and fan speed, It is also not possible to operate in timer or dry mode. Test operation: Test operation switch is the same as emergency switch. [. . . ]