Detailed instructions for use are in the User's Guide.
[. . . ] Inadequate repairs may result in a major source of danger for the user of the air conditioner. Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries. Do not obstruct or cover the ventilation grille of the air conditoner. Do not put fingers or any other things into the inlet/outlet and swing louver. [. . . ] The distance between the indoor unit and the floor should be more than 2m. The appliance is not intended to use by young children or infirm persons without supervision. 9. Young children should be supervised ensure that they do not play with the appliance. 11 . The wiring diagram is attached inside the machine.
Air Conditioner
Edition:2006/01/09
Parts and Functions
Indoor Unit
Inlet grille
Test running switch(manual)
Used only for test running in cooling o when room temp. Don't use it in normal operation.
Emergency switch(manual)
Used when remote controller is lost or defective. Unit will run temporarily.
Remote signal receiver Air filter Vertical flap
Use remote controller to adjust up and down air flow. (Don't adjust it manually. ) A beeping sound is generated when a signal from remote controller is received.
Power indicator
Lights up when unit starts.
Timer mode indicator
Lights up when Timer operation is selected.
Operation mode indicator
Lights up during compressor running.
Actual inlet grille may vary from the one shown in the manual according to the product purchased.
Outdoor Unit
HSU-09C13 HSU-12HF03(B)
HSU-18C13
HSU-22C13 HSU-24C13
OUTLET INLET CONNECTING PIPING AND ELECTRICAL WIRING DRAIN HOSE
Air Conditioner
Edition:2006/01/09
Parts and Functions
Operation
Buttons and display of the remote controller.
1. MODE
Used to select AUTO run, COOL, DRY, HEAT and FAN operation
1 2 3 4
ON/OFF TEMP
5 6 7 8 9
10
AUTO
LO
MED
HI
11 18
MODE SET
Used for unit start and stop.
12
FAN TIMER
19
13. FAN 20
Used to select fan speed LO, MED, HI, AUTO
13 14 15
SLEEP SWING CLOCK
14. RESET
Used to reset the controller back to normal condition.
When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working. setting, unit will run in mild DRY mode.
Hints
On cooling only unit, heating mode is not available. When starting it next time, just press ON/OFF button and unit will run in previous status.
Air Conditioner
Edition:2006/01/09
Operation
(5) Air flow direction adjustment
After operation mode is selected, vertical flap will open automatically according to the mode. COOL About 10o
Up and down (Use remote controller)
Left and right air flow adjustment Press SWING button, vertical flap will move within (manual)
the range shown in the Fig. Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig.
About 10o COOL About 45o HEAT About 60o
Cautions:
It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur.
Cautions:
When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right.
(6) Unit stop
Press ON/OFF button. Vertical flap closes automatically.
Cautions:
Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit.
Hints
As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow downward will be much more helpful for a better air circulation. (2) Press TIMER button to change TIMER mode.
Every time the button is pressed, display changes as follows:
ON
TIMER ON
OFF
TIMER OFF
ON
OFF
blank
TIMER ON-OFF
Select TIMER ON-OFF. "ON" will flash.
(3)Time setting for TIMER ON
Press HOUR button.
Every time the button is pressed, time increases 10 min. AM refers to morning and PM to afternoon
ON/OFF
TEMP
MODE
1 3
SET
6
TIMER
FAN
5
SWING
2
4
CLOCK
SLEEP
(4) Time confirming for TIMER ON
After time setting, press TIMER button to confirm. Time displayed: Unit starts at x hour x min.
LOCK RESET
(5)Time setting for TIMER OFF
Follow the same procedures in "Time setting for TIMER ON".
(6) Time confirming for TIMER OFF
After time setting, press SET button to confirm, "OFF" stops flashing Time displayed: Unit stops at X hour X min.
To cancel TIMER mode
Just press TIMER button several times until TIMER mode disappears.
Air Conditioner
Edition:2006/01/09
Operation
Emergency operation and test operation
Emergency Operation:
Carry out this operation only when the remote controller is defective or lost. [. . . ] When the remote controller is manipulated for the removal, then the selected operation by the remote controller.
Air Conditioner
Edition:2006/01/09
Operation
Comfortable SLEEP
Before going to bed at night, you can simply press the SLEEP button and unit will bring you a sound sleep in selected mode.
In COOL mode
One hour after SLEEP mode starts, temp. won't be too low for your sleep. (As shown in Fig. l)
o o
ON/OFF
TEMP
MODE
SET
FAN
TIMER
SWING
CLOCK
SLEEP
LOCK
RESET
In HEAT mode
One hour after SLEEP mode starts, temp. (As shown in Fig . 2)
SLEEP operation starts SLEEP operation stops Approx. setting
Unit stop
Power Failure Resume Function
If the unit is started for the first time, the compressor will not start running unless 3 minutes have elapsed. [. . . ]