User manual HAIER HSU-12H03/R2

[. . . ] Always remember to unplug the air conditioner before openning inlet grill. Inadequate repairs may result in a major source of danger for the user of the air conditioner. Do not damage any parts of the air conditioner that carry refrigerant by piercing or performating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries. Disposal of the packaging of your new air conditioner All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment. [. . . ] CODE Used to select CODE A or B with a press, A or B will be displayed on LCD. RESET When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal 6. Operation mode display COOL DRY HEAT Parts and Functions Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder) Remove the battery cover: Slightly press " " and push down the cover. ¡/ TM ¨"ª ±, OE °"Õ ª" «Î-- ±º ÿ»° 7# ÿ, § ´µÁ Î `Y £, « µÁ ¬©"«Î Á"^"Ï ÷÷"Û ¿÷ ^, 6 ^°£ ÿ»° `/ "÷­» ÿ°£ ´µÁ ¬µÁ µ£° æ »Î­ Õ« fi<´À £°ºØ ~"­oe ø'µ~ «Î--°"Õ¨"ª¡/ 7# µÁÿ, § ±ºª" ±, OETM ¿÷¬©"«Î´µÁÿ»° ^°£ `/ "÷­»Á"^"Ï£, «Î ´µÁÿ»°^, 6÷÷"Û`Y »Î­¬µÁÿ°£ £°ºØÕ«µ£° ø'µ~~"­oefi<´Àæ «Î--°"Õ¨"ª¡/ 7# µÁÿ, § ±ºª" ±, OETM ¿÷¬©"«Î´µÁÿ»° ^°£ `/ "÷­»Á"^"Ï£, «Î ´µÁÿ»°^, 6÷÷"Û`Y »Î­¬µÁÿ°£ £°ºØÕ«µ£° ø'µ~~"­oefi<´Àæ Load the battery: Be sure that the loading is in line with the" + "/"-" pole request as illustrated. Put on the cover again Confirmation indicator: In disorderation, reload the batteries or load the new batteries after 6mins. Note: Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key. Power failure resume(please set and apply as necessary) If sudden power failure occurs, the unit will resume original operation when power is supplied again. Note: When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is re-supplied, or press ON/OFF to turn off the unit when power resumes. Operation Cool/Dry mode Operation 1. The liquid crystal will display the working state of last time (Except Timer, Power/Soft ). For each press, operation mode changes as follows: Remote controller: COOL DRY HEAT Remote Controller Then select COOL or DRY operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting decrease 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. For each press, fan speed changes as follows: Remote controller: AUTO HI MED LOW Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. Unit stop Press ON/OFF button, the unit stops. 8 Operation Heat Operation 1. The liquid crystal will display the working state of last time (Except Timer, Power/Soft airflow). If the system is operated with the horizontal louver faced completely to the left or right under high humidity (e. g. during the rainy season), dew drops may appear at the outlet. Operation Timer Off Operation Remote Controller With this function, the system stops operating after the designated period. Set clock correctly before starting TIMER operation. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. 2. Set the timer mode to "OFF" by pressing the timer mode switch. Every time the button is pressed, time setting increases 1 h, if kept depressed, it will increase rapidly. Every time the button is pressed, time setting decreases 1 h, if kept depressed, it will decrease rapidly. It can be set from 1 hour to 12 hours 4. Cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. NOTICE Once the remote controller set the timer, the period is memorized. From next time operate easily with operation of the ON/OFF switch and the timer mode swith. After replacing the dry batteries, the designated period is set automatically as follows: OFF: 1 hour, ON: 6 hour. [. . . ] When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner. During unit operation or at stop, a swishing or gurgling noise may be heard. (This noise is generated by refrigerant flowing in the system. ) During unit operation, a cracking noise may be heard. This noise is generated by the casing expanding or shrinking because of temperature changes. [. . . ]