User manual HAIER HSU-09HD03/R2

[. . . ] (Don't adjust it manually. ) A beeping sound is generated when a signal from remote controller is received. Power indicator Lights up when unit starts. Timer mode indicator Lights up when Timer operation is selected. Operation mode indicator Lights up during compressor running. HSU-07HC03/R2 HSU-12HE03/R2 HSU-07HE03/R2 HSU-12HC03/R2 HSU-09HC03/R2 HSU-14HB03/R2 HSU-09HE03/R2 HSU-18HB03/R2 HSU-09HD03/R2 HSU-12HD03/R2 HSU-07HD03/R2 HSU-22HB03/R2 HSU-22HC03/R2 HSU-22HD03/R2 Actual inlet grille may vary from the one shown in the manual according to the product purchased Outdoor Unit HSU-07HC03/R2 HSU-07HE03/R2 HSU-07HD03/R2 HSU-09HC03/R2 HSU-09HE03/R2 HSU-12HE03/R2 HSU-09HD03/R2 HSU-12HD03/R2 HSU-12HC03/R2 HSU-14HB03/R2 HSU-18HB03/R2 OUTLET INLET HSU-22HD03/R2 HSU-22HC03/R2 HSU-22HB03/R2 CONNECTING PIPING AND ELECTRICAL WIRING DRAIN HOSE Air Conditioner Edition:2006/1/10 Parts and Functions Operation Buttons and display of the remote controller. 1. MODE Used to select AUTO run, COOL, DRY, HEAT and FAN operation 1 2 3 4 ON/OFF TEMP ON A U T O 5 OFF 6 7 8 9 10 AUTO LO MED HI 11 18 MODE SET Used for unit start and stop. 12 FAN TIMER 19 13. FAN 20 Used to select fan speed LO, MED, HI, AUTO 13 14 SWING CLOCK 14. RESET Used to reset the controller back to normal condition. When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. [. . . ] Vertical flap closed automatically. Hints Remote controller can memorize settings in each operation mode. To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed. (TIMER ON/OFF needs reelecting) Cautions: Note: On cooling only unit, heating mode is not available, The above information is the After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. No with those displayed in actual Timer mode: No, Fan speed :AUTO operation. Air Conditioner Edition:2006/1/10 Operation COOL, HEAT and DRY operation Recommendations: (1) Unit start Press ON/OFF button, unit starts. (Not Timer setting) Power indicator on indoor unit lights up. Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: ON/OFF TEMP AUTO COOL DRY HEAT FAN 6 1 3 3 SET MODE Unit will run in operation mode displayed on LCD. setting on LCD. 2 FAN TIMER 4 SWING CLOCK 5 SLEEP (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LOCK RESET AUTO LO MED HI COOL operation starts when room temp. setting. Ultra-low air flow Unit runs at the speed displayed on LCD. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. Temp. setting, unit will run in mild DRY mode. Hints On cooling only unit, heating mode is not available. When starting it next time, just press ON/OFF button and unit will run in previous status. Air Conditioner Edition:2006/1/10 Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. COOL About 10 o HEAT About 60o Up and down (Use remote controller) Left and right air flow adjustment Press SWING button, vertical flap will move within (manual) the range shown in the Fig. Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o HEAT About 60o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. Vertical flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit. Hints As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow downward will be much more helpful for a better air circulation. It is harmful to your health in summer to go frequently in and out of places where temp. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON TIMER ON OFF TIMER OFF ON OFF blank ON TIMER ON-OFF Select TIMER ON-OFF. "ON" will flash. (3)Time setting for TIMER ON Press HOUR button. Every time the button is pressed, time increases 10 min. [. . . ] 3 hrs 3 hrs Rises 1oC Note: In AUTO mode, unit will run in SLEEP function according to operation mode. In FAN mode, comfortable sleep is not available. SLEEP mode starts SLEEP mode stops Fig. 2 Air Conditioner Edition:2006/1/10 Maintenance Different models have different appearance Cleaning of unit casing Cut off power supply before cleaning unit casing with soft cloth. squeeze water in the cloth, wipe off the detergent on unit casing completely. Cleaning of remote controller Cleaning of air filter Don't use water to wash unit casing, please use dry cloth. Don't use glass cleaner or cloth soaked with chemicals. Air Filter 1. Open inlet grille by pulling it upward. 3. Clean the filter Use a vacuum cleaner to remove dust, or wash the filter with water. [. . . ]