User manual HAIER HSM22HEA03-R2

[. . . ] Per maggiori informazioni contattare l'installatore o le autorità locali. Le batterie devono essere tolte dal telecomando e smaltite separatamente conformemente alla legislazione locale e nazionale vigente in materia. EN EUROPEAN REGULATIONS CONFORMITY FOR THE MODELS: CE All the products are in conformity with the following European provision: - Low Voltage Directive 73/23/EEC - Low Voltage Directive 2006/95/EC - Electromagnetic CompatibilitY 89/336/EEC - Electromagnetic CompatibilitY 2004/108/EC ROHS The products are fulfilled with the requirements in the directive 2002/95/EEC of the European parliament and of the council on the Restriction of the use of Certain Hazardous Substances in Electrical and Electronic Equipment (EU RoHS Directive). WEEE In accordance with the directive 2002/96/CE of the European parliament, herewith we inform the consumer about the disposal requirements of the electrical and electronic products. DISPOSAL REQUIREMENTS: Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not be mixed with unsorted household waste. [. . . ] Operation mode display 28 Operation mode Remote controller Display board AUTO COOL DRY HEAT FAN 30 17. Singal sending display 18. TEMP button 1. RESET When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal. Control the lightening and extinguishing of the indoor LED display board. Every time the button is pressed, display changes as follows: BLANK POWER SOFT 4. Used for unit start and stop. Used to lock buttons and LCD display. If pressed, the other buttons will be disabled and the lock condition display appears. Press it once again, lock will be canceled and lock condition display disappears. 8. Ambient temp. display When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference. NOTE:(1) The following functions and related displays are not available: (2) Cooling only unit do not have functions and displays related with heating. 6 Parts and Functions Clock Set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: 1. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working. Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. 5. Unit stop Press ON/OFF button, the unit stops. 11 Operation Fan Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI POWER/SOFT 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP and POWER/SOFT operation is not available. 12 Operation Heat Operation Remote controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation 3. Select temp. setting POWER/SOFT Press TEMP. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting decrease 1oC, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed fan speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 13 Operation Air Flow Direction Adjustment 1. Status display of air sending Horizontal louvers Pos. 1 Pos. 2 Pos. 3 Pos. 4 POWER/SOFT Pos. 5 Pos. 6 (Auto swing) 2. Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN: remote controller: HEAT: remote controller: AUTO: remote controller: Pos. 1 Pos. 5 Pos. 1 Pos. 2 Pos. 4 Pos. 2 Pos. 3 Pos. 3 Pos. 3 Pos. 2 Pos. 4 Pos. 4 Pos. 1 Pos. 5 Pos. 6 Pos. 6 Pos. 6 The horizontal louvers will swing according to the above positions. Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position. 14 Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. [. . . ] Every time the button is pressed, display changes as follows: POWER SOFT BLANK Selecting of POWER operation Stop the display at In POWER operation status: In HEAT or COOL mode, fan speed automatically runs in HI mode for 15 min then returns to original status setting. Press POWER/SOFT button twice , POWER/SOFT disappears. To cancel POWER operation SOFT Operation You can use this function when silence is needed for rest or reading. Selecting of SOFT operation Press POWER/SOFT button. Every time the button is pressed, display changes as follows: POWER SOFT BLANK Stop the display at In SOFT operation mode, fan speed automatically takes"LOW" To cancel SOFT operation Press POWER/SOFT button twice , POWER/SOFT disappears. Hints: During POWER operation, in rapid HEAT or COOL mode, the room will show inhomogeneous temperature distribution. [. . . ]