User manual HAIER H2SM-18RA03/R1

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-07RA03/R1(B) HSU-09RA03/R1(B) HSU-12RA03/R1(B) H2SM-18RA03/R1(B) Please read this operation manual before using the air conditioner. No. Cautions Safety Instructions and Warnings Disposal of the old air conditioner Before disposing an old air conditioner that Before starting the air conditioner, read the goes out of use, please make sure it's inopinformation given in the User's Guide careferative and safe. The User's Guide contains very imporin order to avoid the risk of child entrapment. observations relating to the assembly, tant operation and maintenance of the air conditioner. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. [. . . ] For each press, fan speed changes as follows: Remote controller: LOW MED I H AUTO COOL operation starts when room temp. is higher than temp. setting. p s t i n g On reaching temp. setting +2 C unit will run in mild DRY mode. o Air conditioner is running under displayed wind speed In DRY mode, when room temperature becomes 2OC higher than temp. setting, unit will run intermittently at LOW speed regardless of FAN setting. Press ON/OFF button, the unit stops. 5. Unit stop 11 Operation Fan Operation Remote controller 1. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY F AN HEA T Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED I H 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP operation is not available. 12 Operation Heat Operation 1. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY F AN HEA T Then Select HEAT operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly. Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly. Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED I H AUTO Air conditioner is running under displayed wind speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 13 Operation Air Flow Direction Adjustment 1. Status display of air sending direction Vertical flap Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 (Auto swing) 2. Up and down air flow direction For each press of swing button, air flow direction on remote controller or on the control panel displays as follows according to different operation modes COOL/DRY/FAN Pos. 2 Pos. 3 Pos. 4 Pos. 6 remote controller: Pos. 1 : HEAT remote controller: Pos. 5 : AUTO remote controller:Pos. 1 : Pos. 4 Pos. 3 Pos. 2 Pos. 1 Pos. 6 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 The vertical flap will swing according to the above positions 3. Note: When restart after remote turning off, the remtoe controller will automatically memorize the previous set swing position. When making coolness, wind orientation should adjust to the horizontal state in favor of air circulating in the room for cool air will agglomerate upside. When making heat, wind orientation should adjust to the slanting down state in favor of air circulating in the room for hot air will agglomerate downside. 14 Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. SLEEP operation starts SLEEP operation stops Use of SLEEP function A p r o x . 6 h r s After the unit starts, set the operation status, then press SLEEP button before which the Rises 1 C 1 hr clock must be adjusted and time being set. setting so that room 1 hours after SLEEP mode starts, temp temperature won't be too Iow for your sleep. setting so that room temperature won't be too high for your sleep. O O T e m . p s t i n g 1 hr Decreases 2OC 1 hr Decreases 2OC Unit stop 3 hrs 3 hrs SLEEP operation starts Rises 1 C O SLEEP operation stops In HEAT mode 3 In AUTO mode . The unit operates in corresponding sleep mode adapted to the automatically selected operation mode. In FAN mode It has no SLEEP function. Note The sleeping hours lasts 8 hours and couldn't be adjusted. [. . . ] In this operation, the system automatically selects the operation modes, cooling or heating, according to the room temperature. When machine is running in emergency, the set value of temperature and wind speed couldn't be altered; meanwhile, it can't operate for dehumidifying or under timing mode. Operation Test operation: Test operation switch is the same as emergency switch. Use this switch in the test operation when the room temperature is below 16OC, do not use it in the normal operation. After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi". Removal of the restriction of emergency or test operation Press the emergency operation switch once more, or manipulate through the remote controller; the "Pi" sound, the emergency or test operation is terminated. [. . . ]