User manual HAIER DW9-AFM

[. . . ] Use the special plastic support that comes with the appliance (see fig. 2). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. A B Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the dishwasher, making it level. If the appliance is level, it will help ensure proper performance. Cold Water Connection Cleaning the Water Inlet Filter Periodically clean the water inlet filter (see figure 1/A) located on the outlet of the water supply tap. After turning off the water tap, unscrew the end of the water supply hose, remove the filter and clean it carefully under running water. [. . . ] This will help the seals last longer and prevent odors from forming within the appliance. Rinse Remove the Plug Economic, fast cycle to be used for items which are sensitive to higher. 15g Before cleaning or performing maintenance, always remove the plug from the socket. Do not run risks. Moving the Appliance If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be positioned on its back. Glassware No Solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Rather, use only a Pre-wash of dishes, pots and pans while waiting for the load to be completed after Short cold wash to prevent food residue from drying on the dishes cloth and warm soap water. To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little white vinegar, or a cleaning products made specifically for dishwasher. Seals One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a sponge will prevent this from occurring. Soak the subsequent meal. . 7. GB GB . 8. Loading the Dishwasher Starting the Appliance Before placing the dishes in the dishwasher, remove the large food particle to prevent the filter from becoming clogged, which results in reduced performance. If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they be allowed to soak before they are washed. Pull out the rack to facilitate loading the dishwasher. Starting a wash cycle Lower Rack Upper Rack - Make sure that the plug for the appliance is inserted into the wall socket. - Load the dishwasher (see the section entitled, "Loading the Dishwasher"). - Pour in the detergent (see the section entitled, "Salt, Detergent and Rinse Aid"). - Turn the knob located on the right of the control panel in the clockwise direction until the number or symbol for the cycle section entitled, "Wash Cycle Table"). At the end of the wash cycle When the knob stops turning and is aligned with a STOP mark (see figure), the cycle has finished. Turn off the appliance using the ON-OFF button, turn off the water supply and open the door of the dishwasher. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. How to Use the Lower Rack We recommend that you place the items which are the most difficult to clean items on the lower rack: pots, lids, serving dishes and bowls, as shown in the figure to the right. It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm. - The silverware basket can be doubled (see fig. A) so that only one section may be used when the silverware load is light. - Silverware should be placed in the silverware basket with the handles at the bottom; if the rack has side baskets, the spoons should be located individually into the appropriate slots. Especially long utensils should be placed in the horizontal position at the front of the upper rack. 1 2 Load for 9 Standard Settings - Press the ON-OFF button, and the ON-OFF light will turn on. At this point, the wash cycle will begin. Important: In general, it is not advisable to open the door while the machine is working. Care must be taken if the door is opened during the hot phase or immediately after a programm has finished as steam may escape. STOP Cancelling or modifying a wash cycle setting Press the ON-OFF button and the ON Light will turn off. [. . . ] - Do not lean or sit on the door when it is open, as this could overturn the dishwasher. - If the appliance malfunctions, turn off water supply to the appliance and disconnect the plug from the wall socket. - Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock. - The carpet must not obstruct the opening when the appliance installing on the ground with carpet. [. . . ]