User manual HAIER DW45BI

[. . . ] Please note that the guarantee and service availability only apply to the United Kingdom. - If the appliance malfunctions, turn off water supply to the appliance and disconnect the plug from the wall socket. - Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock. - If the supply cord is damaged, it must be replaced by the manufacture, its service agent of similarly qualified persons in order to avoid a hazard. - Fundamental rules to follow when using the appliance: * Never touch the dishwasher when barefoot or with wet hands or feet; * We discourage the use of extension cords and multiple sockets; * During installation, the power supply cord must not be excessively or dangerously bent or flattened; * If the appliance is not operating properly or maintenance must be performed, disconnect the appliance from the power supply. [. . . ] Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Close the door and after a few seconds, a short acoustic signal will sound indicating that the wash cycle has begun and cannot be modified. If necessary, read the paragraph entitled, "Cancelling or modifying a cycle while underway. "The end of the cycle will be signalled by a double acoustic sound, and the indicator light "A" will begin to blink. Setting The Start Delay Time Open the door of the dishwasher partially. If the "I" button is pressed (see, Close-up View" Control Panel"). Each time the button is pressed, the "H" light will come on indicating the length of the delay. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle. . . " There will be a short acoustic signal, and at this point the delay period will begin to count down. At the end of the delay time, the indicator will stop blinking and the cycle will start. 30g Heavy Duty 30g Normal Wash Normal dirty dishes, pots and pans without dried on residue. 30g Cancelling or modifying a cycle while underway. . . A cycle that is underway can only be modified if it has only been running for a short time, otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). Before calling for assistance, Iet us see what can be done first: have you forgotten to press one of the buttons or to perform an essential operation? GB -Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. -There is no advantage in rinsing dishes, cookware and utensils before placing them in the dishwasher. Error Messages The dishwasher is equipped with a safety system that is able to detect operating problems and malfunctions. These malfunctions are signalled by the rapid blinking of one of the "A" program LEDs. Only in the case where the indicator light for the soak cycle (see table for cycles) blinks rapidly should you cancel the cycle as The Dishwasher Does Not Start Have you checked whether: - the plug is pushed into the socket correctly; - the power is on in the house; - the door is closed properly; - the ON-OFF switch is on "ON"; - the water supply is turned on. described in the section entitled, "Changing a Cycle while Underway". Then check to make sure that there is water in the mains and that the tap is turned on. If the message continues, call for technical assistance, indicating which message appeared. If any of the other indicator lights begins to blink rapidly, turn off the appliance and call for technical assistance, indicating which light began to blink. If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised ser- How to keep Your Dishwasher in Shape After Every Wash After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside. When You Go on Holiday When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance. Remove the plug Before cleaning or performing maintenance, always remove the plug from the socket. Do not take risks. The Dishwasher Does Not Load Water Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. Moving the Appliance If the appliance must be moved, try to keep it in a vertical position. If absolutely necessary, it can be positioned on its back. vice centre and provide them with the following information: - the nature of the problem; - the model type number (Mod. . . ) And the serial number (S/N. . . ), which are indicated on the plate located on the side of the inner part of the door. No solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little white vinegar, or cleaning product made specifically for dishwashers. Seals One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. The Dishes Are Not Clean Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts. Cleaning and Special Maintenance Filter Assembly For best performance and results, the filter assembly must be cleaned frequently. [. . . ] The blue wire must be connected to the terminal marked N or coloured black. The brown wire must be connected to the terminal marked L or coloured red. sured door width. Remove the template, and drill pilot holes in the door in all eight positions using a suitable drill (take care not to drill through the door). Attach the upper plastic studs and lower fixing brackets to the decor door as shown below. Stage 8 Cut clearance in the plinth to allow the door to open fully and seal edges with a suitable varnish to prevent water ingress. Stage 4 Position the decor door onto the front of the dishwasher by locating the brackets into the two plastic studs mounted either side on the top of the door. [. . . ]