User manual HAIER DW12-EFM

[. . . ] - Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock. - The carpet must not obstruct the opening when the appliance is Installation Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall, and the sides along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or left to facilitate proper installation. [. . . ] Cleaning the Spray Arms It may happen that food particles become encrusted on the sprayer arms and block the hole (see "Close up view [interior]", letters C-E). Check the sprayer arms periodically and clean them when needed. Close-up View (Interior) A B C H G A D E F B Troubleshooting It may occur that the dishwasher does not function or does not function properly. Before calling for assistance, see what can be done first: have you forgotten to press one of the buttons or to perform an essential operation?The Dishwasher Does Not Start Have you checked whether: - the plug is pushed into the socket correctly; - the power is on in the house; - the door is closed properly; - the ON-OFF switch is on "ON"; - the water supply is turned on. The Dishwasher Does Not Load Water Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. The Dishes Are Not Clean Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. The Dishwasher Does Not Drain Have you checked whether: - the drain hose is crimped or bent. Lime Deposits or a White Film Form on the Dishes Have you checked whether: - the lid of the salt container is closed properly; - the rinse aid dosage is correct. If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised service centre and provide the following information: - the nature of the problem; - the model type number (Mod. . . ) and the serial number (S/N. . . ), which are indicated on the plate located on the side of the inner part of the door. Never call unauthorised technicians and refuse to allow parts to be installed that are not original spare parts. A B C D Upper Rack Rack Height Adjuster Top Spray Arm Lower Rack E F G H Bottom Spray Arm Washing Filter Detergent and Rinse Aid Dispenser Salt Container Cap Technical characteristics Width Depth Height Capacity Mains water pressure Power voltage Total absorber power 60 cm 60 cm 85 cm 12 standard place settings 0. 03-0. 6 MPa 220V-240V~ 50Hz 2100W . 9. GB GB . 2. Salt Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Loading the Salt into the Softener Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: - Remove the lower rack and then unscrew and remove the cap from the salt container; - If you are filling the container for the first time, fill it with water; - Place the end of the funnel (supplied) into the hole and intro duce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container. - Unscrew the cap from the salt container; - On the neck of the container there is a ring with an arrow on it (see figure above). If necessary, turn the ring anti-clockwise from the "-" sign towards the "+" setting, according to water hardness. - It is highly recommended that the following table be consulted when making adjustments. Adjusting Salt Consumption The dishwasher is designed to allow for adjusting the amount of salt consumed according to the hardness of the water used. This is intended to optimise and customise the level of salt consumption so that it remains at a minimum. To adjust salt consumption, proceed as follows: Wash Cycle Table Cycle Cycle Selection Information Description of cycle Detergent Rinse Aid Very dirty dishes, pots and pans (not to be used with delicate Heavy Duty items). Pre-wash with hot water. Normal Wash IEC-EN 50242 30g For dishes that need to be rinsed and dried only. [. . . ] If this is the case, the detergent dispenser must be refilled (see paragraph "Loading the detergent"). Rotate the knob clockwise to the desired cycle setting (see the section "Starting a wash cycle"). Then, turn the dishwasher back on using the ON-OFF button. How to Use the Lower Rack We recommend that you place the most difficult to clean items on the bottom rack: pots, lids, serving dishes and bowls, as shown in the figure to the right. It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm. [. . . ]