User manual HAIER 46EP14S

[. . . ] 2)All warning on the appliance and in the operating instructions should be followed. 4)Attachments ---do not use attachments not recommended by the manufacturer as they may cause hazards. 5)Water and moisture -- do not place this product near water, for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. 6)Accessories ---do not place this unit on an unstable cart, stand, tripod, bracket, or table. [. . . ] 9)Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected. 10)Power cord protection ---Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords or plugs, convenience receptacle, and the point where they exit from the appliance. 11)Lighting precaution ---for added protection for this product during a lighting storm or when it is left unattended for long period of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lighting and power line surges. 12)Never push objects of any kind into this product through openings as they may touch dangerous voltage point or short out parts that could result in a fire or electric shock. 13)Servicing ---do not attempt to service the product by yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. 14)Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. 2 b. If liquid has been spilled, or objects have been fallen into the unit. The S-Video terminal: connects to the Y/C S-Video output of a video output devices(such as S-VHS or DVD). CVBS In terminal connects to the CVBS(Video) output of a device(such as VHS, S-VHS or DVD). The audio should input via Audio 2(INPUT Option Av1). 19 TV module Connect to antenna Input and output connection A/V OUT TV module VHF/UHF: Connect antenna or CATV 75 coaxial cable to receive TV/CATV signal. Video Out: Connect to an input of an external monitor or TV. 20 SPEAKER WIRE SPEAKER WIRE Press the speaker terminals clips down and insert the speakers wire(red to red and black to black), making sure a good contact with the terminal is obtained. Then close the terminal clips. Pg 27 21 Press the POWER key to turn on the Display. The power indicator will change from green back to red. CC RATING SLEEP CC RATING SLEEP TV/CATV 22 and TV module CC RATING SLEEP CC RATING SLEEP 23 & screen adjustments Music Signal source Picture adjustments Channel programing & Picture preference (circular display). The Quick Menu display sequences is as follows: CC RATING SLEEP controls the select function. view time adjusted turn off to turn on the speakers. CC RATING SLEEP 24 Image/picture Format : ASPECT RATIO: by press the WIDE key, you can change the aspect ratio according to your preference . You can then restore the image to its original size by pressing the WIDE key again until your original image is restored. CC RATING SLEEP after zooming in or out. (Only in PC mode) CC RATING SLEEP 25 TV function 26 50 50 50 50 50 50 50 50 50 50 Note: Press / to scroll up & down an / to adjust the settings. 50 50 50 50 TV function For TV function feature please prefer to page 31-32. 27 50 50 50 50 10 10 28 10 10 Display page Image page 50 50 50 50 50 AV1 S-Video YCbCr TV Press menu on display for image page to be displayed. The Image page is used to enable and disable the PIP, set the PIP size and select the PIP source and position. See page 32 for detail information. 29 50 50 50 AV1 PAL 50Hz / 4. 43MHz AV1 PAL 50Hz / 4. 43MHz 30 (7) TV Function Page: O follows: select select 31 select select 32 appear as shown. To change 33 shown below. 34 35 36 8. 37 9. [. . . ] Use this cloth to wipe the surface of the display panel, then wipe it evenly with a dry cloth, of the same type, until the surface is dry. * Do not scratch or hit the surface of the panel with fingernails or other hard objects. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected. *If the cabinet is particularly dirty, soak the cloth in a weak detergent solution and then wring the cloth dry. [. . . ]