User manual HAIER 42EP24S

[. . . ] PLASMA MONITOR WARNING RISK ELECTRIC SHOOK DO NOT OPEN WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel. Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product. The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators or properties: THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT INSIDE. [. . . ] 2 Take care not to touch the stand and the brace pole; 3 Fix the PMMA baffle with the screw 2 M4X8rom the front . Install the Stand to the PDP Face the PDP screen upside down on a clean blanket or the bracket and pay attention not to indent the casing. (See figure) Lay down the stand and put it to responding position of the PDP screen , and make sure the brace pole towards the hole of the PDP . Fix 2 PDP brace pole to the PDP on the back of the plasma display with 4 M5X16 screws. Owner s Manual 15 16 Plasma Monitor Basic Function Saving Mode Hold Q SET button pressed on the remote for 3 seconds until Quick Set mode setup menu appears on the screen. 1. Press 2. Press / / button for desired setup option. button for setup option. Quick Set Setup Light Bright Normal Gray Dark Sound Noise Normal Quiet 3. Press Q SET button (Screen display sees right figure) 4. Press EXIT button to close screen display. (10 seconds later after the latest press, the screen display will disappear automatically. ) Operation Menu 1. Press MENU button to open the main menu. Press 2. Press / button to select submenu, and press / / button to select PIC. , SOU. , ADJ. , SYS. button to increase/decrease the value or select the setup. 3. Press MENU to return to main menu 4. The setup time in display will disappear automatically when the latest preset time expiries. The menu display time can be set to 5, 10, 15, 20, 25, 30 and 40 seconds 5. Press EXIT button to exit any menu if the menu is in display. Sound mode Press S STD button on the remote controller for menu display, and press the mode as follows: / button to change (This feature can also be changed from the sound menu function screen) Sou. Mode Music Standard Theater Personal Music Standard Theater Personal Owner s Manual 17 Picture mode Press P STD button on the remote controller for menu display, and press / button for desired Pic. Mode mode as follows: (This change can also be made from Picture menu adjustment screen) Bright Normal Soft Personal Bright Normal Soft Personal Sleep Timer Every press of SLEEP button, the timer will be set in the following sequence: Sleep 0Min Sleep 5Min Sleep 15Min Sleep 30Min Sleep 60Min Sleep 90Min Sleep 120Min Sleep 0Min If remaining time of set timer is to be displayed, press the SLEEP button once. AV1/S-Video/YPbPr/YCbCr/VGA/DVI Play 1. Press INPUT button on the remote controller, the following menu will appear on the screen. Press / button for option and then press / button or ENTER to confirm. Source Note: If AV1 and S-Video are inserted at the same time, priority will be given to S-Video. AV1/S-Video YPbPr/YCbCr VGA DVI 18 Plasma Monitor Picture Quality Adjust Picture quality adjust Picture quality can be adjusted for any input separately. Press MENU button and AV1/S-Video menu: / until the following menu appears on the screen: 50 50 50 0 50 A B C YPbPr/YCbCr menu: 50 50 50 0 50 (Not available) A B C (Not available) VGA menu: 50 50 50 0 50 (Not available) A B C (not available) Owner s Manual 19 Picture quality adjust DVI menu: 50 50 50 0 50 (not available) A B C (not available) 2. Press 3. Press / / button to enter picture menu and to select desired option , the current item is marked yellow. When displayed time for menu setup expires without any operation , the menu disappears from the picture , If MENU or EXIT button is pressed , the menu on display will disappear in sequence or immediately respectively. Note: 1. When Personal mode is not selected, the Personal mode can be entered automatically if Contrast, Brightness, Color, Tint and Sharpness parameters are adjusted. 2. Noise Reduction mode DNR can be set to Auto, Off, Weak, Medium or Strong. 20 Plasma Monitor Sound adjustment Sound adjust Sound can be adjusted for any input as follows: 1. / button to enter sound setup menu, and press again for desired option. 3. Repeat step 2 and 3 until desired sound has been achieved when displayed time for menu setup expires without any operation , the menu disappears from the picture . If MENU or EXIT button is pressed , the menu in display will disappear in sequence or immediately respectively. A B C Note: 1. Select Balance to balance right and left sound channels of the monitor . When indication value of Balance increases toward +50, sound of the right and left speaker becomes stronger and weaker, respectively. When indication value of Balance decreases toward -50, sound of the right and left speaker becomes weaker and stronger, respectively. 2. When Personal mode is not selected, the Personal mode can be entered automatically if Treble or Bass parameters are adjusted. his feature maintains a fixed volume for different levels of programmaterial, like loud commercials. Owner s Manual 21 Adjustment Setup Adjusting setup In VGA and DVI input mode , H Position and V Position can be used to adjust the picture position. Press MENU button on the remote controller and option of picture position adjust. [. . . ] In such case, If buttons on monitor are pressed, the screen will display Child Lock, which can be erased by press of EXIT button. 5 seconds later after the latest press, the screen display will disappear automatically. The Child Lock mode can be resumed by entering Lock Set menu to set Child Lock off or active Unlock. Max Volume Press button to select Max Volume. If a / / certain value is set, when volume is being adjusted, the sound value cannot exceed maximum volume value. [. . . ]