User manual H2O AUDIO S9-1A3

[. . . ] If you experience any resistance when closing the housing please call customer service immediately at 1. 800. 708. 6080 x213 before using your housing. Cleaning & Storing the T-Seal It is extremely important that you keep the T-Seal clean & free of sand, dirt, hair, lint, and other debris. Correct This T-seal is correctly seated in a closed housing, sealing the housing and protecting the iPod from water. Wash T-Seal in warm fresh water, ensuring all debris is cleaned from the T-Seal. *Strong detergents, soaps, and chemicals MUST NEVER be used to clean the Housing or the T-Seal. * Allow T-Seal to air dry. Please refer to the "How to install / replace your T-Seal" on how to properly install the T-Seal. 6. [. . . ] Installing the iPod into the Housing Installing the iPod 1 1 1. Close the lid, and hook the buckle under the base. Contact Surfaces iPod nano Housing Water IT IS EXTREMELY IMPORTANT YOU ENSURE THE T-SEAL IS PROPERLY SEATED DURING EACH CLOSURE. If it is out of alignment, or twisted you will cause damage to or destroy your iPod. 2 2 1. Align the audio port with the stereo jack in the housing. IMPORTANT: Remove any skins or covers from your iPod before installing it into the housing. 2. Verify the player is completely plugged into the audio jack. Prior to use, verify: Do NOT use if: 2. While holding the latch button towards the unlock icon, push up on the side of the latch. 2. T-Seal is aligned properly in the Contact Surface of the lid prior to closure. 1. T-Seal is twisted, or out of alignment during closure. Compatible with 2nd Gen iPod nano 2. T-Seal and contact surface have been cleaned as necessary using a soft, lint-free cloth. 2. T-Seal and Contact Surfaces have any dirt, lint, hair, and/or other debris. Removing the iPod 1. Now the player can slide straight out of the housing. 3. 3 T-Seal and Contact Surface are free of scratches and other imperfections. 3. You see scratches or imperfections on the T-Seal or Contact Surfaces. 3. Unhook the buckle from the base. and the button is positioned on the icon prior to entering the water. DO NOT USE SILICONE GREASE as this will damage the seal. To ensure the T-Seal is fully seated in the base of the housing, firmly squeeze both sides (the base and lid) of the housing together after each insertion of the player. Always check to make sure the latch is closed and locked prior to use. If you have any questions or doubts, please contact H2O Audio Customer Support NOTE: Do not disturb the T-Seal during removal of the player. If the T-Seal is moved, Please use the housing lid to completely seat the T-Seal. S9 - 70 20061013 8. Connecting the Headphones The SealTight Connector is what keeps your audio connection safe and dry underwater. It is designed specifically to create a seal around the H2O Audio Series Waterproof Headphones (sold separately). Using any other headphones will not have a complete waterproof connection, and reduces the waterproof rating to water-resistant. TM 9. Commander Scroll Wheel Control The Commander Scroll Wheel Control is a waterproof assembly, which allows you to maintain complete control over the iPod's Click wheel functions. Refer to iPod Instruction Manual for complete details of how to use the player. TM TM 10. General Storage Procedures For long-term storage, store in a plastic bag out of direct sunlight. [. . . ] Service or modifications by anyone other than an Authorized H2O Audio agent will void the warranty. H2O Audio will not be responsible for recovery or replacement of the product in the event of loss or theft. H2O Audio, its Authorized International Distributors, and Authorized Dealers make no other warranties, either express or implied or orally, or in writing, with respect to any other warranty coverage except those expressly stated within the preceding sentences. H2O Audio will not be held responsible for any agreements orally or in writing with the exception of those expressly included in this warranty statement. [. . . ]